Duct Board

ACOUSTICAL DUCT LINER Aeroflex PLUS®

Aeroflex PLUS® Acoustical Duct Liner has been reformulated to reduce dust and irritation and is used to enhance indoor environmental quality by absorbing noise within sheet metal ducts and contributing to indoor comfort by lowering heat loss or gain through duct walls. It is thermally effective, has a tough abuse-resistant, cleanable surface and meets fire resistance codes

CAT. NO. MFG. NO. SIZE 8H957 8H948 8H987 8H960 8H971

8H9870 8H9871 8H9873 8H9874 8H9875

200 150 300 150 150 150 150 150 150 150

1/2” x 47-1/2” x 100’ 1” x 35-1/2” x 100’ 1” x 47-1/2” x 50’ 1” x 47-1/2” x 100’ 1” x 60” x 100’

1-1/2” x 35-1/2” x 75’ 1-1/2” x 47 -1/2” x 75’ 2” x 35-1/2” x 50’ 2” x 47-1/2” x 50’ 2” x 59-1/2” x 50’

INSTALLED R-FACTOR EACH R 1.9 R 3.6 R 4.2 R 3.6 R 3.6 R 6.0 R 6.0 R 8.0 R 8.0 R 8.0

$381.12 $336.49 $489.00 $476.80 $602.27

$612.68 $482.47

FLEXFLOW ELBOW

The elbow installs over the duct in a matter of seconds at Diffusers and round taps using an adjustable system similar to a zip tie. No tools are required. One size fits 6” - 16” Flexduct. Packaged 25/box.

CAT. NO. MFG. NO. 4G6637D 050800000001

DESCRIPTION EACH FlexFlow elbow

$11.90

FLEX-DUCT CUTTERS

Double-edge blade cuts duct and liner; built-in wire cutter cuts wire rib coil. FDC3 is very similar to the FDC1 however, it incor- porates a wire tie-tensioning device.

CAT. NO. MFG. NO. DESCRIPTION 1X481

1X481B 1X482

FDC1 FDC3 TP601

Flex-Duct Cutting Tool

Flex-Duct Cutting Tool, Multi-Purpose Leather Belt Sheath for FDC1

EACH $83.73

$121.92 $23.70

ROUND HOLE CUTTER

for Duct Board

Cuts smooth, accurate 4 to 20” diameter holes in 1” fiberglass ductboard quickly and easily. Uses standard utility knife blade.

CAT. NO. MFG. NO. DESCRIPTION 1X474

FG1 4G7578 KBHC

Fiberglass Duct Hole Cutter 1-1/2” Ductboard Blade

EACH $79.17 $10.37

DuraTite PLASTIC DUCT TAKE-OFFS

The DuraTite plastic duct takeoffs with damper are installed by the unique “Zip & Clip” system. Installs in ½ the time. The DuraTite takeoffs are a high quality polypropalene and glass mixture which makes it durable, and air tight, as well as dent proof, rust proof and non-conductive. No tabs to bend back, no sharp edges, and can be used with 1”, 1 ½” ,2” ductboard as well as metal ducting. Use with flexduct, or metal duct. Double sided adhesive gasket for air tight seal. Damper accsessed from outside of takeoff and can be adjusted to 6 dif- ferent positions for air balancing.

CAT. NO. MFG. NO. SIZE EACH 8H776R 8H777N 8H777P

DTK0604 DK0704 DK0804

6” dia 7” dia

8” dia $13.57

Visit us at www.remichel.com

907

DUCT, REGISTERS & GRILLES