CONVENTIONAL OPEN-TYPE COMPRESSORS (Belt Drive)

A complete line of conventional open-type compressors from 1/2 HP through 10 H.P. Dura- bility and availability of parts coupled with ease of service are just a few reasons why there are over 2 million Blissfield compressors operating in the field. All compressors are com- pletely tested prior to leaving the factory and are shipped with mineral oil. All compressors shipped with suction and discharge shut-off valves and flywheel. Excellent replacements for Tecumseh, Frick, and Bitzer open compressors. Rated for use with R-12, R-134A, R-404A, R-407C and R-507 refrigerants - high, medium and low temperature applications.

CAT. NO. MFG. NO. HP 9R4001 1HVS

9R4002 2GVS 9R4003 9R4004

3LVS

SUCT. VALVE

1/2 - 1 5/8” mfl 1 - 3 3 - 5

3/4” mfl

DISC. VALVE 1/2” mfl 5/8” mfl

1-1/8” mfl 3/4” mfl

FLYWHEEL DIA. 6.3” 6.3”

10.6” 41VSM/3B 5 - 10 1-3/8” ods 1-1/8” ods 12” BELT &

GROOVES 2 A 2 A 3 A 3 B

WEIGHT EACH

38 lbs 49 lbs 84 lbs

209 lbs

$1,126.43 $642.86

$2,589.32 $5,529.69

Note: Mounting kits available on special order to allow mounting on same footprint as older style Blissfield compressors.

UNIVERSAL MOUNTING BASE for all compressors

Mount replacement residential air conditioning and commercial refrigera- tion compressors in minutes. No drilling required - uses existing mounting holes. Allows compressor to be mounted in any position most suitable to line up with

original refrigerant and electrical connections. Kit includes tem- plate and all mounting bolts and hardware.

CAT. NO. MFG. NO. EACH 1R185

SK-23 $19.82 QwikLug™

COMPRESSOR TERMINAL REPAIR KIT

Patened QwikLug™ compressor terminal repair kit is designed to repair damaged or corroded compressor terminals in seconds. No more bruised knuckles! Easy to insall from the front with a screwdriver.

Includes durable brass connector, 10 AWG-2 ft. leads with nut. 3 terminals repair lugs/bag.

CAT. NO. MFG. NO. EACH 8G0301

QT2810 $52.68 COMPRESSOR LEAD KIT

Kit includes (3) leads, each consisting of: flag female compressor terminal (.250 tab; part 6259), waterproof butt connector (12-10 wire range; part 62231), piece of 10 gauge wire (12”).

CAT. NO. MFG. NO. EACH 6E709

60259HX $19.04

2. When in doubt, turn the power off, disconnect the wires from the compressor and measure the ohmic resistance between the terminals. The highest resistance will be from S to R. The next highest resistance will be from C to S and the lowest resistance will be from C to R. From these measure- ments, you can determine the actual individual terminal designations.

The above isn’t as complicated as it sounds. Simply draw three “terminals” on a piece of paper in the configuration of the terminals on the compressor you are checking. Label them A,B,C, or what ever you want to label them. Begin measuring the resistances and noting them on the paper.

Example:

term (A) to term (B) = 4.5 ohms term (A) to term (C) = 2.0 ohms term (B) to term (C) = 6.5 ohms

Conclusion: A to B is = to C to S (Middle reading) A to C is = to C to R (Lowest reading) B to C is = to S to R (Highest reading)

Therefor:

(A) term is actually Common (C) (B) term is actually Start (S) (C) term is actually Run (R)

Visit us at www.remichel.com 669

ELECTRICAL CHECKS ON HERMETIC COMPRESSORS

ID the terminals... 1. Terminals are (C) Common, (S) Start, and (R) Run. They are always read “Left to Right, Top to Bottom”

2GVS 3LVS

41VSM

REFRIGERATION EQUIPMENT & SUPPLIES