GAS FIRED CONDENSING STAINLESS STEEL BOILER - WATER ONLY

The Alpine boilers are “Made in America” and utilize a stainless steel heat exchanger designed to extract maximum heat from the combustion process, along with a control system to provide full modulation at a 5 to 1 turn down ratio, outdoor reset, and domestic hot water priority. The boiler requires no additional components for use with LP gas. A simple adjustment of existing components facilitates use with LP gas. The boiler is shipped with a 2 pipe, CPVC/PVC venting package for side wall venting, or “thru-the- roof” venting (CPVC/PVC vent kit for use with solid core PVC piping only). “Snorkle” installations up to 7 feet are approved with the CPVC/PVC venting. Maximum vent length for intake and exhaust venting is 60 equivalent feet each. Simple connections, all gas, water, and electrical connections are made from the left side of the boiler, vent connections on lower back of boiler. Boiler shipped with circulator control, and relief valve, less circulator.

CAT. NO. MFG. NO.

2W780A ALP080F-1L02 80,000 2W781A ALP105F-1L02 105,000 2W782A ALP150F-1L02 150,000 2W783A ALP210F-1L02 210,000 2W784A ALP285F-1L07 285,000 2W785A ALP399F-1L07 399,000

MFG. NO.

73,000 96,000

137,000 193,000 263,000 377,000

63,000 83,000 119,000 168,000 229,000 328,000

ON HEAT EXCHANGER

Alpine Series

ON PARTS* RESIDENTIAL APPLICATIONS

ON PARTS** RESIDENTIAL APPLICATIONS

* 2W780 thru 2W784 ** 2W785 only

BTU INPUT MAX BTU INPUT MIN OUTPUT NET IBR A.F.U.E.% EACH 16,000 21,000 30,000 42,000 57,000 80,000

95 95 95 95 95

94.1 DIMENSIONS H x W x D

ALP080F-1L02 32-3/16 x 16-11/16 x 12-9/16” 1” ALP105F-1L02 32-3/16 x 16-11/16 x 14”

1”

ALP150F-1L02 32-3/16 x 16-11/16 x 19-11/16” 1” ALP210F-1L02 32-3/16 x 16-11/16 x 23-15/16” 1” ALP285F-1L07 43-7/16 x 16-11/16 x 21-13/16” 1-1/4” ALP399F-1L07 43-7/16 x 16-11/16 x 28-7/8”

1-1/2”

1-1/4” 1-1/2”

1/2” 1/2” 1/2” 1/2” 3/4” 1”

3” 3” 4” 4” 4” 4”

3” 3” 3” 3” 4” 4”

$5,462.68 $6,030.78 $7,026.16 $7,888.09 $11,039.19 $14,636.32

SUPPLY RETURN GAS CONN. VENTING INLET VENTING EXHAUST WEIGHT 1” 1” 1” 1”

137 lbs 155 lbs 182 lbs 206 lbs 256 lbs 304 lbs

ACCESSORIES FOR BURNHAM ALPINE BOILERS CAT. NO. MFG. NO. DESCRIPTION

EACH 3W399A 102097-01 Hydrolevel low water cutoff for alpine boilers $276.78

RECOMMENDED CIRCULATORS FOR BURNHAM ALPINE BOILERS

It is crucial to the operation of the boiler that proper water flow through the boiler is maintained. Insufficient water flow through the heat exchanger can cause damage and contribute to premature failure. Conversely, excessive water flow can cause erosion and excessive noise. In an effort to maintain an adequate flow, the following circulators are recommended for use with the Burnham Alpine series boilers.

BOILER MODEL CIRCULATOR MODEL ALP080 ALP080 ALP105 ALP150 ALP210 ALP285 ALP399

Taco 0010 Grundfos 15-58 FRC

Grundfos UP26-99 FC (first speed) Grundfos UP26-99 FC (first speed) Grundfos UP26-99 FC (third speed)

CAT. NO. 5W306 5W618

Grundfos UP26-99 FC (second speed) 5W6250 5W6250 5W6250 5W6250

Grundfos UPS32-80/2 (second speed) SPECIAL ORDER

Note: The above recommendations are based on 25 degree delta T and up to 75 ft. equivalent length near boiler piping. Installations exceeding these parameters will require different circulator selections.

EACH

$471.88 $186.10 $536.71 $536.71 $536.71 $536.71

362

BOILERS