AIR CONDITIONING & HEATING EQUIPMENT

GAS-FIRED MOBILE HOME FURNACES with/without Built-in Coil Cavity

The M1MB series furnaces are gas fired models, air conditioning ready, with/without coil cavity built-in. These furnaces are sealed combustion, venting exhaust gas directly outdoors and drawing 100% outside air for combustion. High efficiency drum heat exchanger with fully insulated cabinet for quiet operation and to minimize heat loss. Appliance quality door with baked enamel finish. Furnaces must be vented with F/SAW series roof jacks. Shipped complete with gas burner with HSI ignition, forced draft, con- trols, LP conversion kit and air filter. 115 vac. - 1/2” gas connection. Complete accessory selection available for use in new and replacement applications.

CAT. NO. MFG. NO.

FACTORY SET BTU

3B165 M1MB-056A-BW 56,000 3B166 M1MB-070A-BW 70,000 3B167 M1MB-077A-BW 77,000 3B168 M1MB-090A-BW 90,000 3B155 3B156 3B157 3B158

M1MB-056A-AW* 56,000 M1MB-070A-AW* 70,000 M1MB-077A-AW* 77,000 M1MB-090A-AW* 90,000

* Unit does not have coil cavity built-in.

OUTPUT BTU

45,000 57,000 62,000 72,000 45,000 57,000 62,000 72,000

AC READY MAX TONS 3 3 3 3 3 3 3 3

FUSE AMPS 15 15 15 15 15 15 15 15

M1MB Series

ON HEAT EXCHANGER

ON PARTS DIMENSIONS H x W x D WEIGHT EACH

76 x 19-3/4 x 23-3/4” 76 x 19-3/4 x 23-3/4” 76 x 19-3/4 x 23-3/4” 76 x 19-3/4 x 23-3/4” 56 x 19-3/4 x 23-3/4” 56 x 19-3/4 x 23-3/4” 56 x 19-3/4 x 23-3/4” 56 x 19-3/4 x 23-3/4”

167 lbs $1,660.98 168 lbs $1,774.98 167 lbs $1,834.18 168 lbs $2,117.23 161 lbs $1,473.77 162 lbs $1,478.94 161 lbs $1,669.00 162 lbs $1,954.70

ACCESSORIES FOR M1MB SERIES MOBILE HOME FURNACES CAT. NO. MFG. NO. DESCRIPTION

EACH

3B919 3B934 3B900 3B922 3B923 3B924 3B926 3B927 3B928 3B930 3B905 3B907 3B910 3B911 3B912 3B140 3B141 3B142

903413 903890 901083

Blower Assembly 2-4 ton

Blower Assembly Upgrade (5 ton) Automatic Cavity Damper

903658 FAW1523-0A Roof Jack 903659 FAW2135-0A Roof Jack 903660 FAW2747-0A Roof Jack 903662 SAW2135-2A Roof Jack 903663 SAW2747-2A Roof Jack 903664 SAW3563-2A Roof Jack 903666A SAW5195-4A Roof Jack 901935 901937

$466.93

EI10A-5 Flue Extension EE16A-5 Flue Extension

$150.00 $156.15 $166.89 $205.14 $166.89 $205.14 $263.29 $388.80 $76.53 $58.16

901987A Plenum Connector 11.25 x 13.5 x 0.88” $52.03 901988A Plenum Connector 11.25 x 13.5 x 2.0” $52.03 901990A Plenum Connector 11.25 x 13.5 x 6.25” $52.03 903893 903894 903895

Pitch Adapter for Roof Jack 2.5” in 12” $58.16 Pitch Adapter for Roof Jack 3” in 12”

$58.16 Pitch Adapter for Roof Jack 3.5” in 12” $58.16

GOOD PRACTICES

When replacing a piece of fossil fuel fired equipment it’s always good practice to physically inspect the chimney flue, and the availability of proper combustion air, prior to offering a quote to the homeowner. Check the flue for blockages and/or offsets and turns before quoting on replacement. This practice will eliminate additional costs after the replacement of the equipment. Remem- ber, a restricted/blocked flue may have been the problem which caused the existing equipment to be replaced. At very least, the ex- isting flue should be thoroughly cleaned and resealed to prevent heat loss and poor heat absorption. At the worse case, the chimney may require an aluminum liner (for gas equipment) or a stainless steel liner (for oil equipment). Proper combustion air availability can be checked against NFP-54 specifications, or the manufacturer’s Installation and operation manual.

218