SWG Series VENT KIT

for 80+ Draft Induced Furnaces

The SWG Sidewall Power Venter solves the flue gas leakage problem because it

uses negative pressure to pull gases completely through the system. With negative pressure, flue gases cannot leak through joints or cracks because air is being pulled into any opening in the vent pipe rather than being pushed out into the inhabited space. The SWG adds additional peace of mind with safety features that prevent the furnace from igniting until sufficient draft is established to ensure safe and proper venting.The SWG-4G is available for ALL gas fired 80+ mid-efficiency draft induced furnaces. This kit includes a CK-43F Control Kit with a non-adjustable post purge and a 4” MG-1 Barometric Draft Control. This kit includes instructions for each of these specific furnace manufacturers: Amana, Armstrong, Bard, Carrier, Consolidated, Dunkirk, ICP, Lennox, Rheem, Trane and York.

CAT. NO. MFG. NO. MAX. BTU PIPE CONNECTIONS EACH 6H196

SWG-4G 140000 4” $830.08 DRAFT REGULATORS

The Field draft regulators are all pre-as- sembled ready for installation. RC & B34 models are designed for oil or coal appli- ances with flue sizes from 4” to 10”.MG1 is used for commercial gas fired furnaces and boilers with 4-8” flue sizes.

M + MG2 is for gas, oil/gas, oil and coal-fired furnaces and boil- ers sized from 10” thru 25” with natural, induced or forced draft. Thermal type switch can be wired to operate an alarm in case of blocked flue or backdraft.

CAT. NO. MFG. NO. 6H221 6H215

6H085A 6H099 6H100 7G046 6H101

17H2525 6H098 6H088 6H102 6H103 6H104 6H105 6H106 6H107 6H108 6H109

B34C03 4RC 5RC 6RC 7RC 8RC 9RC

4MGI 6MG1 7MG1 8MG1

SIZE FITS SMOKE PIPE SIZES EACH 3” 4” 5” 6” 7” 8” 9” 4” 6” 7” 8”

3” 4”

4, 5, 6” 5, 6, 7” 6, 7, 8” 7, 8, 9”

8, 9, 10” 4”

5, 6” 6, 7” 7, 8”

10M + MG2 10” 12M + MG2 12” 14M + MG2 14” 16M + MG2 16” 18M + MG2 18” 20M + MG2 20” 24M + MG2 24”

9, 10”

11, 12” 13, 14” 15, 16” 17, 18”

19, 20, 21” 22, 23, 24, 25” GALVANIZED FINISH

CAT. NO. MFG. NO. SIZE FITS SMOKE PIPE SIZES EACH 6H199G 6H099G 6H100G

B34-5 B34-6 B34-7

5” 6” 7”

5” 6” 7”

$34.46 $34.02 $39.99

$42.16 $48.11 $69.42 $62.88 $74.80

$103.74 $135.80 $117.65 $146.25 $156.31 $202.16 $338.65 $442.01 $573.93 $803.47

$1,068.63 $1,277.37 $1,564.28

“FAN IN A CAN™” for Oil Fired & Gas Fired Equipment

These models are designed for use on systems where direct connections to the heating appli- ance with outside combustion air isn’t possible. They draw outside combustion air into the heat- ing appliance area on call for heat and once intake air movement is proven, send a call for heat to the heating unit. Systems come complete w/4” intake air hood, Fan-in-a-Can assembly, 6” to 4” reducer and restrictor plate.

CAT. NO. MFG. NO. DESCRIPTION 5G3200A CAS-3 5G3200B CAS-4

EACH

110v, for oil fired equipment 24v, gas fired equipment

$565.76 $565.76

TEE JOINT DRAFT REGULATORS

Accurate draft control and easy installation for oil. coal and wood-fired equipment. Gates are supported on minimum-friction type bearings and are adjustable for sensitiv- ity. Constructed of heavy gauge black steel

CAT. NO. MFG. NO. SIZE EACH 6H110 6H111

5RC/BT 6RC/BT

5” 6”

$113.46 $115.80

RING & GATE ASSEMBLIES

“M” series damper assemblies for installa- tion on oil and coal-fired equipment where there is an existing collar or tee. Gate operates on minimum-friction bearings and is adjustable for sensitivity. Fits flush with end of pipe opening.

CAT. NO. MFG. NO. SIZE EACH 6H113 6H114 6H115 6H116

6M 7M 8M 9M

6” 7” 8” 9”

$120.22 $140.11 $177.55 $189.43

894

AIR HANDLING & VENTING PRODUCTS