Previous Page
Miscellaneous Controls
CAD CELL PRIMARY RELAY ELECTRONIC OIL BURNER
PRIMARY CONTROLS Cad Cell Relays for 4 x 4 box mounting
The 8245 features a 45 second trial for ignition, constant duty control with lock out indicator and safety monitoring circuit. 40200-02 features a 15 second trial for ignition, interrupted duty control with recycle on flame capabilities and safety monitoring circuit. Increases lifespan of ignition trans- former & electrodes and reduces power consumption.
The 42230 features a 30 second trial for ignition, interrupted duty control with recycle capabilities and safety monitoring circuit. Increases lifespan of ignition transformer & electrodes and reduces power consumption.
The 50200-02S features a 15 second trial for ignition, interrupted duty microprocessor based control. Full recycle, safety monitor- ing circuit, reset protection (3 tries and latchup) w/alarm contacts. Prepurge and diagnostic LED’s.
The 60200-02S features a 15 second trial for ignition, interrupted duty microprocessor based control with all the benefits of 50200. Pre-purge, post-purge and diagnostic LED’s. Excellent choice for powered side wall vent applications.
The 24638 is an instant opening oil valve kit with lines & fittings. CAT. NO. MFG. NO.
7G193 7G194 4H638
48245
40200-02 42230
EACH $93.92
$101.89 $101.89
CAT. NO. MFG. NO. 7G999 7G998
EACH
50200-02S 60200
$123.06 $134.59
BC Series BLOWER CONTROL
EZ-TEMP™ 90000 MICROPROCESSOR
TEMPERATURE CONTROL
The EZ-Temp™ 90000 microprocessor tem- perature control is ideal for use on hydronic
heating and domestic water applications requiring “operating and high limit” control. The EZ-Temp™ control has independent con- tacts for both operating and high limit control which are monitored by the “safety monitoring circuit” top insure correct operation. This solid state control includes LED diagnostics to indicate power, call for heat, and lockout/latch-up. Should the control “lockout”, reset is accomplished by holding the reset button for 10 seconds until the green LED flashes, and than for another 20 seconds for the red LED to turn off and the control to reset. Specs: 120V - 10 amp max. Limit range: 100-240°F
CAT. NO. MFG. NO. DESCRIPTION 4H668
EACH 90000A-2S EZ-Temp™ 90000 control $141.01
4H668B 90000B-2S EZ-Temp™ 90000 control for Bock water heaters $155.20 4H668A 9886-1AS Well kit for above
$44.51 830
Delays the on and off times of the blower fan resulting in increased heating efficiency. Incorporates a safety limit input circuit required for safe operation of forced air furnaces. Electrical rating: 24 VAC. Control circuit: 120/240 VAC load.
CAT. NO. MFG. NO. RANGE 3Z039
BC-7070 0-4 Min. adj. Blower-On/Off Time
EACH $85.38
Relay mounts to a standard 4” x 4” junction box, with connections for 2 wire, 24V thermo-
stat to control a line voltage burner. No need to replace the cad cell assembly, as this control is compatible for use with existing Honeywell, or White-Rodgers cad cell assemblies. External push- button reset. Replaces Honeywell R8184G4009, R8184G1138, R8184G1427, R8184G4025; Carlin 48245; Heil 1147017; White- Rodgers 668-401.
CAT. NO. MFG. NO. AMPS @120v SAFETY TIMING EACH 1C444E
ICM1503 7.4 45 seconds $71.19
COMMERCIAL
MOTOR PROTECTOR 3 PHASE
This control is fully programmable. Monitors
front and back side of the system with 25 fault code memory stor- age. Voltage range 190-630 volts. Can be programmed as manual or auto reset. Monitors the following: voltage unbalance, high/low voltage, phase loss, reversal, incorrect sequencing and prevents rapid short cycling. Replaces Watsco EAC800 and EAC8000.
CAT. NO. MFG. NO. DESCRIPTION 1Q083
ICM450 EACH 3 Phase Motor Protector $280.51
FAST-STAT 5000 THERMOSTAT MULTIPLEXER
The Fast-Stat 5000 eliminates the need to re-pull thermostat cables when adding or upgrading equipment. Provides R, C, G, Y, W1, and W2 control over a 2-wire cable. Can also be used with 4 or 5-wire thermostat cables to provide 8 or 9-wire control.
CAT. NO. MFG. NO. DESCRIPTION 2F180
5000 EACH FAST-STAT 5000 Wiring Extender $290.10
CONTROLS