Z-VENT III

AL29-4C® STAINLESS STEEL VENT SYSTEMS for High Efficiency Gas Boilers

The greatly reduced stack temperatures of modern 80%+ efficiency gas-fired heating equipment has made it possible to vent many fur- naces and boilers through stainless steel vent pipe. And, since the flue gases of higher efficiency combustion produce acidic condensate which rapidly deteriorate metal vent systems, the choice of an acid and corrosion resistant Z-Vent System, where recommended by the equipment manufacturer, is even more logical. Z-Vent is UL listed and is available in popular 3” and 4” diameter sizes.

Note: In order to comply with manufacturers’ requirements for sidewall venting, Z-Vent III fitting connections are fitted with hi-temper- ature silicon gaskets. No need for additional sealant unless gaskets are torn. Always follow the equipment manufacturers instructions. AL29-4C® is a registered trademark of Allegheny Ludium Steel Corporation.

3” DIAMETER

CAT. NO. DESCRIPTION 2H924 2H946 2H909 2H906 2H910 2H907 2H925 2H922 2H923 2H917 2H919 2H916 2H915

Horizontal Condensate Drain Pipe Utica “DV & USC” Series Adapter Locking Band Termination Tee Wall Thimble

Termination Box

Vertical Condensate Drain Pipe 3” 45° Angle 3” 90° Elbow

3” x 3 ft. Vent Pipe 3” x 5 ft. Vent Pipe 3” x 2 ft. Vent Pipe 3” x 1 ft. Vent Pipe

EACH $70.74 $38.03 $21.69 $70.65 $58.86 $70.40 $88.00 $79.78 $90.83 $80.00

$143.75 $64.15 $31.82

CAT. NO. DESCRIPTION 2H930N 2H932N 2H933N 2H934N 2H939N 2H938N 2H927N 2H944N 2H945N 2H942N 2H943N 2H908 2H941 2H947

4” DIAMETER 4” x 1 ft. Vent Pipe

4” x 2 ft. Vent Pipe 4” x 3 ft. Vent Pipe 4” x 4 ft. Vent Pipe 4” 90° Elbow 4” 45° Angle

4” x 3” Reducer

Horizontal Condensate Drain Pipe Vertical Condensate Drain Pipe Termination Tee Termination Box Locking Band Wall Thimble

Utica “DV & USC” Series Adapter Z-VENT SEALANT

EACH $38.12 $69.85 $90.40

$126.06 $96.28 $83.85 $53.72 $99.60

$101.48 $77.69 $77.69 $24.42 $60.95 $45.82

CAT. NO. DESCRIPTION 2H911

3 oz. Tube Z Vent Sealant

EACH $25.51

Patented No-Calk® flashing slips over plastic vent pipe, providing weather- tight seal without caulking around pipe.

Allows vent to expand and contract without breaking seal; adjusts to roof pitch from 0 to 40°. Meets UPC, SBC and BOCA codes, approved by FHA.

ROOF

CAT. NO. VENT PIPE SIZE EACH 4H131 4H132 4H133

FLASHINGS 2”

3” 4”

$14.57 $16.04 $18.94

REPLACEMENT

ROOF CAPS for Miller

CAT. NO. MFG. NO. 9Z136 1H181

104360000 104359000

SIZE EACH 4” 5”

$81.47 $101.77

STAINLESS STEEL FLUE LINER

Stainless steel chimney liner is the ideal solution to the problem of upgrading an unlined chimney for use with oil or solid fuel heating equipment. Eliminates the need for expensive replacement of masonry chimneys or installation of externally mounted all-fuel chimneys where outside appearance is imported. Construction is of 26 ga. #302-2B nickel bearing, heat resisting stainless steel for maximum service life.

3’ LENGTH PIPE 90° ADJ. ELBOW CAT. NO.

CAT. NO. 9H201 9H202 9H203 9H204

SIZE EACH 5” 6” 7” 8”

$151.74 $151.74 $151.74 $176.40

9H205 9H206 9H207 9H208

SIZE EACH 5” 6” 7” 8”

$88.37 $93.91

$104.02 $122.31

TEE

CAT. NO. 9H213 9H214 9H215 9H216

SIZE EACH 5” 6” 7” 8”

$139.46 $146.49 $155.31 $186.26

PLUG, CRIMPED CAT. NO.

9H217 9H218 9H219 9H220

SIZE EACH 5” 6” 7” 8”

$46.44 $50.67 $48.07 $56.71

RAIN CAP

CAT. NO. 9H221 9H222 9H223 9H224

SIZE EACH 5” 6” 7” 8”

$131.60 $129.56 $80.61

$166.67

880

AIR HANDLING & VENTING PRODUCTS