PRESSURE RELIEF VALVES for Hot Water Boilers
This series of valves is designed to be used on hot water boilers, not steam boilers. They work on a pressure basis only, and should be located at the top of the boiler. Tested and rated by the National Board of Boiler and Pressure Vessel Inspectors; and listed and rated by ASME.
Stainless steel test lever is standard on all sizes. 374A has an iron body with forged bronze inlet. 174A series valves are for hot water space heating boilers, bronze rust-proof construction, assuring safety and long life. 740 series valves are for hot water space heat- ing boilers, iron body, with increased discharge capacities. ASME rated and listed relief capacities at press setting shown.
2K786 2K785 2K800 2K801 2K804 2K805 2K790 2K791 2K792 2K793 2K794
CAT. NO. MFG. NO. SIZE FPT INLET x OUTLET 3/4” x 3/4” 3/4” x 3/4” 3/4” x 3/4” 3/4” x 3/4”
M335M1* 335M1 374A 174A 174A 174A 740 740 740 740 740
5G4011 174A**
RATED BTU CAPACITY @ 30 LBS 510,000 510,000 550,000 650,000
1-1/4” x 1-1/4” 1,682,000 1-1/2” x 1-1/2” 2,020,000 3/4” x 1”
925,000 1” x 1-1/4” 1,300,000
1-1/4” x 1-1/2” 2,105,000 1-1/2” x 2” 2” x 2-1/2” 3/4” x 3/4”
2,900,000 5,250,000 950,000
EACH
$77.59 $44.86 $75.87 $99.83
$496.52 $504.76 $172.24 $281.55 $430.31 $596.10 $857.38 $109.68
CONBRACO PRESSURE RELIEF VALVES 4G8534 10-408-05 3/4” x 3/4”
CAT. NO. MFG. NO. SIZE FPT INLET x OUTLET RATED BTU CAPACITY @ 30 LBS 535,000
EACH $25.53
TEMPERATURE & PRESSURE RELIEF VALVES
for Gas & Electric Water Heaters
A self-closing combination temperature and pres- sure relief valve for protection of gas-fired hot water heaters, storage tanks and range boilers. Valve is ASME listed and certified by AGA. All bronze body with stainless steel spring. Thermo- static element has a special coating which forms a dielectric barrier to prevent accumulation of mate- rial deposits and galvanic corrosive action. Male
inlet and female outlet. Test lever is standard. Temperature relief is set at 210°F.
CAT. NO. MFG. NO.
2K413 2K557 2K556 2K555 2K570*
10L-2
100XL-3-125 100XL-3-150 100XL8
L100XL-3
SIZE PRESSURE RELIEF SETTING 75 lbs.
3/4” 3/4” 3/4” 3/4” 3/4”
125 lbs. 150 lbs. 150 lbs. 150 lbs.
AGA BTU/ HR. RATING
80,000
105,000 105,000 105,000 105,000
EACH
$21.61 $24.62 $26.38 $24.20 $9.04
*Extended inlet model. For heaters with thick jacket insulation up to 2” thick.
CALIBRATED PRESSURE RELIEF VALVE
Calibrated adjustment allows for setting the valve to required pressure relief. Adjustable range 50-175 psi. Not ASME approved.
CAT. NO. MFG. NO. SIZE 5G4002
530C EACH 1/2” FPT x 1/2” MPT $48.45
CAT. NO. MFG. NO. SETTING EACH 2K411
2K411B
53L-150 53L-125
150 lbs 125 lbs
$30.64 $28.18
PRESSURE RELIEF VALVES
For protection against excessive pressure. Used on domestic storage tanks or tankless water heat- ers.
Furnished in 1/2” size inlet and outlet. Does not comply with ASME requirements. Bronze body and stainless steel spring.
TEMPERATURE & PRESSURE
RELIEF VALVES for Oil-fired Water Heaters
Fully automatic temperature and pressure relief protection for hot water supply tanks and heaters. Bronze body construction with non-mechanical seat-to-disc alignment that will not stick or freeze.
Standard with test lever and 5” thermostat for installation in hot water outlet or directly in available tank tappings. Valve is 5-1/2” high (less thermostat), certified by CSA and meets current FHA requirements. Temperature relief set at 210°F.
2K814 2K815
CAT. NO. MFG. NO. SIZE PRESSURE RELIEF SETTING 125 lbs. 150 lbs.
40XLS 40XLS
3/4” 3/4”
AGA
BTU/HR. RATING 205,000 205,000
EACH
$166.93 $166.93
STEAM SAFETY VALVES
For low pressure steam heating boilers. All brass construction with flat seat and teflon faced disc for positive seal and non-sticking. ASME listed. Set at 15 psi.
CAT. NO. MFG. NO. INLET
2K830 2K831 2K832 2K833
315-M1 3/4” MPT 13-202-08 1” MPT OUTLET
3/4” MPT 1” MPT
STEAM DISCHARGE CAPACITY LB./HR. SET 15 LBS 300 643
13-213-08 1-1/4” MPT 1-1/2” MPT 1200 13-214-B15 1-1/2” MPT 2” MPT
1900 EACH
$41.82 $88.53
$153.13 $205.63
480
HYDRONIC & STEAM SYSTEMS