MODEL A AND B FUEL UNITS

Compact and highly reliable fuel units designed for quiet, efficient operation. Convenient side porting provides easier installation and ad- justment. Piston-type valve assures steady pressure and fast, consistent cut-off even at high RPM, 2-bolt flange mount. Rotation and nozzle location are viewed at shaft end.

MODEL A --- SINGLE STAGE

Recommended for single or two-pipe installations, either lift or gravity feed. Maximum allowable lift is 8 ft. for single-pipe, 10 ft. for 2-pipe systems. May be mounted in any position. Discharge pressure adjustable from 100-200 PSI. Inlet and return ports 1/4” FPT. Nozzle port 1/8” FPT. Shaft dia. 5/16”. Maximum firing rate 4 GPH at 100 PSI design pressure.

CAT. NO. MFG. NO. SPEED RPM

1P304 A1YA-7912 1725

1P304A A1YB-7913 1725 1P304B A1YC-7914 1725 1P308 1P309 1P310 1P311 1P312

A2VA-7116 3450 A2VB-7117 3450 A2VC-7118 3450 A2YA-7916 3450 A2VA-3006 3450

Flange Flange Flange Flange Flange Flange Flange Flange

MOUNT SHAFT ROTATION R.H. (CW) R.H. (CW)

NOZZLE LOCATION R.H. L.H.

L.H. (CCW) L.H. R.H. (CW) R.H. (CW)

L.H. (CCW) L.H. R.H. (CW) R.H. (CW)

R.H. L.H.

R.H. L.H.

MODEL B --- TWO STAGE

Capable of handling high lift, long line installations. Provides automatic, extremely fast priming on two-pipe applications with a maximum 18 ft. lift. Pump may be mounted in any position, except upside down. Discharge pressure adjustable from 100-200 PSI. Inlet and return ports 1/4” FPT. Nozzle port 1/8” FPT. Shaft dia. 5/16”.

CAT. NO. MFG. NO. SPEED RPM

1P316 1P320

B1VA-8212 1725 B2VA-8216 3450

4G1084 B2YA-8916 3450

MOUNT SHAFT ROTATION R.H. (CW) R.H. (CW) R.H. (CW)

Flange Flange Flange

NOZZLE LOCATION R.H. R.H. R.H.

EACH

$270.57 $228.75 $225.81

EACH

$127.29 $159.56 $159.56 $124.44 $198.76 $198.76 $156.68 $105.53

MODEL H --- TWO STAGE FUEL UNITS

The Model H has higher firing rate capabilities than the Model A and B series. Quiet operation, balanced fast cut-off, leak-proof shaft seal and con- venient porting are but a few features of this outstanding unit. Available for either 2-bolt flange or set-screw hub mounting. Rotation and nozzle location are viewed at shaft end.

The Model H has an extremely fast priming pump recommended for two-pipe, high-lift conditions up to 15 ft. maximum. Flex- ible, three position mounting. Discharge pressure adjustable, from 90-150 PSI. Inlet and return ports 1/4” FPT. Nozzle port 1/8” FPT. Shaft dia. 7/16”. Maximum firing rates at 100 PSI rated pressure: H3 --- 7 GPH at 1725 RPM, 20 GPH at 3450 RPM; H6 --- 20 GPH at 1725 RPM, 55 GPH at 3450 RPM.

CAT. NO. MFG. NO. MOUNT SHAFT ROTATION NOZZLE LOCATION EACH 1P088

H3BB-200 Hub R.H. (CW) L.H. $425.63

566

FUEL OIL SYSTEMS