Sump & Transfer Pumps

LIQUID REFRIGERANT TRANSFER PUMP PEDESTAL SUMP PUMP

The vertical sump pump is designed for residential and light to moderate commercial duty. Engineered to handle the tough, demanding tasks of dewatering with high efficiency and long term dependability. This pump is also ideal for applications containing small debris. Features include a 1-1/4” FNPT discharge, adjustable

on/off level, 8’ power cord, corrosion-proof polypropylene volute, and a snap-action float switch. Outlet is 1-1/4” MPT.

CAT. NO. MOTOR HP 1/3

1E985

MOTOR VOLTS 115

GPH @ 5 ft.

2800

GPH @ 10 ft. 2040

GPH @ 15 ft. 620

WEIGHT EACH 16 lbs. $276.49 SUBMERSIBLE SUMP PUMP

For residential and light commercial use. 1-1/2” FNPT discharge with a maximum lift of 18’. Polycarbonate cover and polypropyl- ene volute-base. Cast iron pump housing with protective epoxy coating for corrosion and

rust resistance. Oil filled motor housing for lifetime lubrication and rapid heat dissipation. Stainless steel screws, bolts and handle. Mechanical seal (stainless steel spring, nitrile parts, carbon and ceramic faces).Thermal overload protection. Automatic operation with pressure switch operates pump when water level is between 7” and 10”. Pump shuts off when water level falls to between 1” and 4”. Outlet is 1-1/2” FNPT. (Pressure switch is non-adjustable).

CAT. NO. MOTOR HP 1/3

1E988

MOTOR VOLTS 115

WEIGHT GPH @ 5 ft.

17.5 lbs. 2750

GPH @ 10 ft. 1750

GPH @ 15 ft. 750

EACH $303.00 EPOXY-CLAD PUMP

Can be totally submerged in water, dilute acids, scale removers or solvents. 115v AC. 2R330 includes 6’ power cord. 2R330A - ac- cessory hose kit contains 20 ft. vinyl tubing, 2

male hose adapters, 2 hose clamps and 1 stainless steel hose clamp.

CAT. NO. GPH @ 1 ft. GPH @ 3 ft. GPH @ 6 ft. GPH @ 12 ft. EACH 2R330

300 240

CAT. NO. DESCRIPTION 2R330A

Accessory Hose Kit 180

EACH $74.93

PORTABLE FUEL TRANSFER PUMP

A self-priming gear pump specifically designed to pump uncontaminated light oils. Features 1/2 HP, 120v motor with power cord and switch, Buna mechani- cal seals and O-ring cover, cast iron pump with stainless steel shaft, carbon- graphite bearings and heat treated

gears. Inlet/outlet connections are 3/4” FPT; flow rate - 6.5 gpm.

CAT. NO. MFG. NO. EACH 4P341

2116 $2,886.65 45 $421.73

STA-RITE SELF-PRIMING TRANSFER AND UTILITY PUMP

A high speed pump capable of handling large quantities of water for transfer- ring from tanks, draining boilers and water heaters or emptying flooded basements. NOT to be used for fuel oil or solvent. For water only. 3450 RPM

motor is rated for continuous duty. Equipped with capacitor starter, stainless steel shaft, permanently lubricated bearings, 3-wire power cord with grounded plug, carrying handle and permanent mounting bracket. Inlet/outlet connections are 1” NPT; 115 volt AC.

CAT. NO. MFG. NO. MOTOR HP EACH 4P340

DPC

10 15 20

5 ft. 43 39 30 18

10 ft. 37 35 26 15

1/2

15 ft. 27 27 22 10

$719.40

DISCHARGE PERFORMANCE IN GALLONS PER MINUTE PRESSURE SUCTION LIFT --- HEIGHT OF PUMP ABOVE WATER P.S.I. 5

20 ft. 15 15 15 7

UTILITY PUMP Self-priming, Rated at 360 gph

These flexible impeller pumps are well suited for pumping water from drums, tanks, sumps, etc. but should not be used to transfer petroleum

based liquids. For water only. Self-priming 8-10 ft. vertical suc- tion; discharges 40 ft. vertically or 200 ft. horizontally. Pump shaft is stainless steel. Impeller, O-rings and seals are Buna N. The 115v AC motor has automatic thermal overload and is fitted with a 6 ft., 3-wire grounded cord and plug. Includes garden hose and suction strainer.

CAT. NO. MFG. NO. 4P345 4P346

DESCRIPTION FPOF360AC Utility Pump FPOO3414S Rebuilt Kit for F360 Pump

5 ft. 10 ft. 20 ft. 30 ft. 40 ft. 320 300

240 145 62 EACH

$277.13 $23.24

CAPACITY, GALLONS PER HOUR AT DISCHARGE HEAD

For recovery and reclaim systems, fully compatible with R-11, R-12, R-22, R-113, R-114, R-121, R-134a, R-404, R-500, R-502, R-507 refriger- ants and all compressor oil types. Use for unit-to-cylinder or cylinder-to-cyl- inder transfer. 1/2 HP, 115 volt motor,

rated flow is 38 lb. per min. Inlet and discharge are 1/2” NPT.

CAT. NO. MFG. NO. EACH 4P342

001661 $3,636.87

492

HYDRONIC & STEAM SYSTEMS