This content requires Adobe Flash Player version
or later.
Either you do not have Adobe Flash Player installed,
or your version is too old,
or there is a problem with your Flash installation and we were unable to detect it.
FACET FUEL PUMPS These original, American made fuel pumps are for carburettor engines. Suitable for petrol and diesel fuels with all additives. All have a built in anti-siphon and anti drain-back valves. Simple two bolt installation. For best results mount as close to the fuel tank as possible below the fuel level and always use a filter between the tank and pump. Rubber mountings are recommended (see our mounts section)
ELECTRONIC FUEL PUMP Reliable solid state internals, no electrical contacts to burn out, no bearings to wear and no diaphragms to perish. 12 volt. Less than 2 amp current drain. Will self prime up to 0.3mtrs lift. Footprint 80mm x 80mm x 60mm high (without unions). 2 bolt fixing at 65mm centres. Union thread size 1/8" npt. Weight 469gm. Operating temperature range -31 to +55 deg C. ROAD Will pump from 2.5 psi to 3.5 psi. Flow rate 113 ltrs/ hour (30 US gal/hr.) #FAC1 £35 each (£42 inc vat) COMPETITION Will pump from 4 psi to 7 psi. Flow rate 128 ltrs/hour (34 US gal/hr.) #FAC2 £39 each (£46.80 inc vat)
ONLINE
360° VIEW
ELECTRONIC FUEL PUMP Sealed, reliable solid state internals. 12 volt. Requires separate earth connection to pump body via fixing bolt. Less than 2 amp current drain. Will self prime up to 1 mtr lift. Footprint 140mm x 82mm x 85mm high (without unions). 2 bolt fixing at 65mm centres. Removable, washable internal nylon filter. Weight 760gm.
Operating temperature range -60 to +43 deg C.
FAST ROAD Will pump from 5 psi to 6 psi. Flow rate 132 ltrs/hour (35 US gal/hr.) Union thread size 1/8" npt. #FAC3 £70 each (£84 inc vat)
ONLINE
360° VIEW
COMPETITION Will pump from 6.5 psi to 7 psi. Flow rate 151 ltrs/hour (40 US gal/hr.) Union thread size 1/4" npt. #FAC4 £74 each (£88.80 inc vat)
PLATED STEEL FUEL FILTER FOR #FAC1 , 2 and 3 1/8" NPT to 8mm push on tail.
#FF188 £3.50 (£4.20 inc vat)
BRASS 90 DEGREE HOSETAILS FOR #FAC1 , 2 and 3 #HT90186 1/8" NPT to 6mm push on tail. #HT90188 1/8" NPT to 8mm push on tail. #HT901810 1/8" NPT to 10mm push on tail.
All £4 each (£4.80 inc vat)
BRASS STRAIGHT HOSETAILS FOR #FAC4 #HT14NPT8 1/4" NPT to 8mm push on tail #HT14NPT10 1/4" NPT to 10mm push on tail.
BRASS STRAIGHT HOSETAILS FOR #FAC1 , 2 and 3 #HT186 1/8" NPT to 6mm push on tail. #HT188 1/8" NPT to 8mm push on tail. #HT810 1/8" NPT to 10mm push on tail.
All £4 each (£4.80 inc vat) All £4 each (£4.80 inc vat)
BRASS 90 DEGREE HOSETAILS FOR #FAC4 #HT9014NPT8 1/4" NPT to 8mm push on tail. #HT9014NPT10 1/4" NPT to 10mm push on tail.
All £4 each (£4.80 inc vat)
ONLINE
360° VIEW
Page 78
To order Tel: 01580 891309 or 07964 336183 or Fax: 01580 893733