This content requires Adobe Flash Player version
or later.
Either you do not have Adobe Flash Player installed,
or your version is too old,
or there is a problem with your Flash installation and we were unable to detect it.
BRASS 90 DEGREE HOSETAILS #HT90186 1/8" NPT to 6mm push on tail #HT90188 1/8" NPT to 8mm push on tail #HT901810 1/8" NPT to 10mm push on tail All £4 each (£4.80 inc vat)
RED M10 x 1mm ANODISED ALUMINIUM STRAIGHT HOSETAILS with sealing washer #HT1018AR M10 x 1 to 8mm Red Aluminium hosetail. #HT10112AR M10 x 1 to 12mm Red Aluminium hosetail #HT10115AR M10 x 1 to 15mm Red Aluminium hosetail All £5.50 each (£6.60 inc vat)
BRASS STRAIGHT HOSETAILS #HT186 1/8" NPT to 6mm push on tail #HT188 1/8" NPT to 8mm push on tail #HT810 1/8" NPT to 10mm push on tail All £4 each (£4.80 inc vat)
BLUE M10 x 1mm ANODISED ALUMINIUM STRAIGHT HOSETAILS with sealing washer #HT1018AB M10 x 1 to 8mm Blue Aluminium hosetail. #HT10112AB M10 x 1 to 12mm Blue Aluminium hosetail #HT10115AB M10 x 1 to 15mm Blue Aluminium hosetail All £5.50 each (£6.60 inc vat)
BRASS STRAIGHT HOSETAILS FOR #HT146 1/4" BSP to 6mm push on tail #HT148 1/4" BSP to 8mm push on tail #HT1410 1/8" BSP to 10mm push on tail
All £4 each (£4.80 inc vat)
GOLD ANODISED ALUMINIUM STRAIGHT HOSETAILS #HT14NPT12A 1/4" NPT to 12mm push on tail #HT14NPT15A 1/4" NPT to 15mm push on tail All £5.50 each (£6.60 inc vat)
BRASS STRAIGHT HOSETAILS #HT14NPT8 1/4" NPT to 8mm push on tail #HT14NPT10 1/4" NPT to 10mm push on tail All £4 each (£4.80 inc vat)
PTFE TAPE General thread sealing tape ideal for oil, air and water fittings. 12mm wide x 10 metres roll. #PTFE £1 (£1.20 inc vat)
BRASS 90 DEGREE HOSETAILS #HT9014NPT8 1/4" NPT to 8mm push on tail #HT9014NPT10 1/4" NPT to 10mm push on tail
All £4 each (£4.80 inc vat)
We cannot guarantee that the appearance and/or colours of products shown in this catalogue exactly reproduce the appearance and/or colours of the physical products themselves. All sizes quoted are approximate
Page 378
THREAD LOCKING / SEALING COMPOUND We don't know why we haven't stocked this before but here it is - better late than never. A great way to lock nuts and bolts or any threaded component to prevent them coming loose from shock and vibration. It has the added benefit of sealing the thread against moisture and corrosion and will seal pipework and joints on oil, fuel and water systems. Works best when components are thoroughly degreased. Fully cures in 45 to 60 minutes. 10 gms. #THLOCK £4 (£4.80 inc vat)
To order Tel: 01580 891309 or 07964 336183 or Fax: 01580 893733 ISSUE 27