Replacement Blower Parts
BLOWER WHEEL PULLER
Fast and easy! A simple method to remove blower wheel from shaft without damage to blower, blower motor or shaft. Contains 1-1/4”, 1-3/8”,1-1/2” and 1-5/8” hub sizes.
CAT. NO. MFG. NO. DESCRIPTION 9R1031 6R1026
CD3570 CD3510
EACH Blower Wheel Puller Kit Drive Bolt, Shank and 1-3/8” Hub
$251.77 $123.45
Note: re-lube with SAE 20 or 30 wt. non-detergent oil. Temp. range: Min. 40° F, Max. 135° F.
OIL SLEEVE BEARINGS with Insulator
Self-aligning, self-oiling with sintered bronze bushings and drive type oil cups.
CAT. NO. SHAFT DIA. O.D.SIZE EACH 6L308 6L843
3/4” 1”
1-27/32” 1-27/32”
PILLOW BLOCK SLEEVE BEARINGS
Heavy neoprene cushion. Re-oilable porous bronze bushing in a pressed steel ball unit, firmly held in a housing of two piece inter-
OIL SLEEVE BEARINGS with Insulator
Self-aligning, self-oiling, with bronze bushing held in housing under light, uniform spring pressure, which provides uniform distribution of lubricant through pores of bushing, drive type oil cup.
CAT. NO. SHAFT DIA. O.D.SIZE EACH 6L840 6L841
5/8” 3/4”
1-13/16” 1-13/16”
$39.24 $47.77
Note: Shipped dry-lube at time of installation with SAE 20 or 30 wt. non-detergent oil. Temp. range: Min. 40° F, Max. 135° F.
SEALED SLEEVE BEARINGS
Self-aligning, factory packed with a supply of plas- tic petroleum, assuring proper lubrication during life of bearing. Temp. range: Min. 40° F, Max. 135° F.
CAT. NO. SHAFT DIA. O.D.SIZE EACH 6L1000
3/4” 2-1/16” OIL SLEEVE BEARINGS
Self-oiling with sintered bronze bushings and drive type oil cups. Temp. range: Min. 40° F, Max. 135° F.
CAT. NO. SHAFT DIA. O.D.SIZE EACH 6L1002 6L1003
3/4” 1”
2-1/16” 2-1/16”
CARTRIDGE SLEEVE BEARINGS
This cartridge type bearing has been designed to give you fast, easy interchangeability. It will fit any “spider type” bracket used on 9”, 10”, 12” blowers. Sintered bronze bushing pressed into steel bearing caps and cushioned in heavy neoprene conductive rubber. Factory packed with lubricant for many years of quiet, trouble-free service.
CAT. NO. SHAFT DIA. 1Q700 6L850 1Q699
872
3/4” with thrust collar and spacer 3/4” with Journal 1”
O.D.SIZE EACH 1-13/16” 1-13/16” 1-13/16”
$41.59 $86.01 $34.84
$32.36 $31.99
$28.82
locking steel. Self-aligning, static free and quiet operation. This high quality pillow block will assure many years of trouble-free performance. Two 1/8” rubber spacers provided for use if needed. Temp. range: Min. 40° F, Max. 135° F.
CAT. NO. MFG. NO. 6L305 6L306 6L307
38-2204-0 1 38-2086-01 38-2087-01
SHAFT DIA. EACH 5/8” 3/4” 1”
$24.65 $28.62 $24.95
SEALED BALL BEARINGS with Insulator
For use when operating conditions exceed the limits of sleeve bearings or where repetitive failures occur. These bearings are pre-lubricated at the factory and require no further lubrication or attention. They are equipped with seals to retain grease better and to protection against contaminants. Temp. range: -20° F, +180° F.
CAT. NO. SHAFT DIA. 8L1000 8L1001
3/4” with interlocking thrust collar 3/4” with interlocking thrust collar
O.D.SIZE EACH 1-13/16” 2-17/32”
$77.75 $84.97
SLEEVE SEALED BEARINGS with Insulator
Self-aligning, factory packed with a supply of plastic petroleum assuring proper lubrication dur- ing long life of bearing. Self-aligning porous bronze sleeve pressed in housing. Temp. range: Min. 40° F, Max. 135° F.
CAT. NO. SHAFT DIA. O.D.SIZE EACH 1Q703 1Q704 1Q705
5/8” 3/4” 1”
1-13/16” 1-13/16” 2-1/2”
$37.58 $34.29 $40.16
UNIVERSAL BEARING BRACKET-SHAFT KIT
Re-oilable bearings, complete with shaft, in bracket for replacement on all belt driven blowers. Kit contains two brackets with bearing housed in spherical rubber liner to eliminate vibration; assuring quiet and constant self align- ment. Kit includes thrust collars and spacers.
CAT. NO. SHAFT SIZE EACH 6L301 6L302
3/4” x 20” 1” x 25”
$122.40 $122.10
$38.03 $35.46
AIR HANDLING & VENTING PRODUCTS