780 Series HOT SURFACE IGNITION MODULES
The 780 Series hot surface ignition modules are designed for use on gas fired heating systems. They provide lockout and complete gas shut off if ignition is not proven after the trial for ignition sequences has been completed. To reset the system the thermostat or system switch must be opened for at least 10 seconds. Features include molded-in terminal barriers between terminals, mount- ing screw that provides a positive ground connection and small compact size provides easy installation. Ambient temperature: -40 to 176°F. Operating humidity: 95% @ 104°F.
Model 780-783 has 34 sec. pre-purge/igniter warm-up timer and replaces Rheem part no. 62-22578-01.
Model 780-785 has 34 sec. pre-purge/igniter warm-up timer and replaces Rheem part no. 62-22578-02.
Model 780-790 has 17 sec. pre-purge/igniter warm-up timer and replaces Rheem water heater part no. 41-AP10758.
CAT. NO. MFG. NO. VOLTAGE EACH 6C094
5G2002 6C096
780-783 780-785 780-790
120 120 120
$203.15 $196.01 $234.77
UNIVERSAL IGNITION MODULE KITS
These kits will replace over 300 com- petitive modules including Penn-Baso
CSA42A, CSA45A, CSA49A, G600 Series, G60, G65, G66 and G67 Series modules as well as the Honeywell models listed below.
CAT. NO. MFG. NO. DESCRIPTION 6C085 6C086
780-001 780-002
HONEYWELL NO. S8610A1009 S8610F1008 S8610F1016 S86A1001 S86A1019 S86A1027 S86A1035 S86B1009 S86B1017 S86B1025 S86E1002 S86E1010 S86E1028 S86E1036 S86E1044 S86E1051 S86E1069
EACH
Universal Ignition Module Kit (non-lockout) Universal Ignition Module Kit (lock-out)
REPLACES HONEYWELL MODELS: UNI-LINE NO.
780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001
HONEYWELL NO. S86E1077 S86E1101 S86E1119 S86E1127 S86F1000 S86F1018 S86F1026 S86F1042 S86F1059 S861067 S86F1075 S86F1083 S86F1091 S86G1008* S86H1006* S86H1014** S90A1005
* Original control had 90 second timing lockout timing. ** Original control had 15 second lockout timing.
780 Series PILOT IGNITION REPLACEMENT CONTROL
The “K” Series pilot ignition system gas valve was used with ignition control
units SP710, SP710A and SP720. These ignition control units are obsolete and this modernization kit is designed to replace them. The modernization kit will upgrade the old heater sensor/flame switch system to flame rectification. Wire harness and gas valve are not included in the kit.
Replaces the following: 780-701, 780-710, 780-712, SP710, SP710A, SP720-919-01 and SP720-909-1 thru SP720-909-4.
CAT. NO. MFG. NO. DESCRIPTION 6G803
780-705 EACH Pilot Ignition Replacement Control $257.86 IGNITION CONTROL UNITS
780-715, SP715U is a non-lockout model featur- ing the flame rectification system. Use with gas valves 7000 BDER, 7100 DER and 7200IPER.
780-735, SP735A is a lockout model featuring the flame rectification system and 60 second lockout timing. Use with gas valves 7000 BDER and 7100 DER.
CAT. NO. MFG. NO. DESCRIPTION 6C090 6C092
780-715 780-735
EACH
SP715U Non-Lockout Model $200.23 SP735A, Lock-out Model
5500 Series INFINITE CONTROLS UNI-KITS®
Offers unusually wide variety of input regulation applications. Has shunt type heater to control resistive loads to 15 amps, and provides nominal low input of 5% and infinite inputs up to 100%. At high setting control is energized continuously, at other settings it delivers selected level of input. Off position gives double line disconnect. Electrical rating: 15 amps at 120v and 240v AC.
CAT. NO. MFG. NO. DESCRIPTION 6C945 6C946 6C950
5500-103 5500-203 5500-202
818
120 volt, w/Black Dial 240 volt, w/Black Dial 240 volt, Less Dial
EACH $52.93 $51.40 $43.85
$286.37
$567.92 $231.00
UNI-LINE NO. 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-001 780-002 780-002 780-002 780-001
CONTROLS