EQUIPMENT & ACCESSORIES CATALOG EDITION IV CRYO-SEM & CRYO-FIB/SEM PREPARATION SYSTEMS
zzzCryo Transfer Systems (continued)
SPECIFICATIONS for PP3004, PP3005, PP3006 PP3004
Temperature Cooling Runtime LN2 Dewar Capacity
Cool-Down Time to -190°C Rapid Freezing (slushy LN2) Dewar Trolley Footprint Airlock Weight
Pumping Requirements Nitrogen Gas
Ambient N/A N/A N/A N/A N/A
2.5 kg Rotary pump or dry pump For venting and valve operation
Power Requirements (excluding pump) 300 W Maximum Specimen Size
PP3005
RT to -190°C Up to 24 hours 21 liters
Typically <15 minutes Optional (24429) 50 x 50 cm 2.5 kg
Rotary pump or dry pump Venting and cooling 300 W
PP3006
RT to -190°C Up to 24 hours 21 liters
Typically <15 minutes Optional (24429) 50 x 50 cm 2.5 kg
Rotary pump or dry pump Venting and cooling 300 W
Flat specimens up to 23 x 26 mm. For taller specimens the maximum height will reduce from a mid-point of 9mm. Please contact us for more details.
ORDERING INFORMATION For a full quotation, including on-site installation and customer training, please contact us. Pumping
PP3004
QuickLok Ambient Temperature Transfer System Includes:
Airlock assembly. Pump and vent and transfer controls, valve and fittings to the pumping system (see: Pumping below). Custom designed interface flange to the microscope vacuum chamber
Microscope dovetail stage to accept specimen shuttle. LED chamber light (interlocked)
Specimen transfer device for vacuum or inert gas transfer Specimen holders. Specimen shuttle with holding clips, specimen shuttle blank, specimen shuttle (to hold a 10mm dia. specimen stub), blank 10 mm stubs – packet of 10
PP3005
SEMCool Non-Airlock Low Temperature System Includes:
Nitrogen gas cooled cold stage with heater and sensor and cold trap with temperature sensor. Temperature controllable with a range down to -190°C, 21 L liquid nitrogen dewar with trolley, heat exchanger and LED chamber light. Pump fittings (see: Pumping below).
Temperature and nitrogen gas flow controller mounted on the dewar trolley.
Specimen holders. 3 specimen shuttles (to hold 10 mm Ø cryo stubs), blank specimen shuttle, specimen shuttle with holding clips, blank 10 mm Ø stubs (packet of 10), 5 multi-purpose specimen stubs. Note: other holders available Specimen mounting compounds (colloidal graphite and Tissue-Tek®
) PP3006
CoolLok Cryo Transfer System Includes:
Airlock assembly. Pump and vent and transfer controls, gate valve and fittings to the pumping system (see: Pumping below). Custom designed interface flange to the microscope vacuum chamber. Cooling system. Nitrogen gas cooled cold stage with heater and sensor and cold trap with temperature sensor. Temperature controllable with a range down to -190°C, 21 L liquid nitrogen dewar with trolley, heat exchanger and LED chamber light. Specimen transfer device
Specimen holders. 3 specimen shuttles (to hold 10 mm Ø cryo stubs), blank specimen shuttle, specimen shuttle with holding clips,blank 10 mm Ø stubs (packet of 10), 5 multi-purpose specimen stubs. Note: other holders available Specimen mounting compounds (colloidal graphite and Tissue-Tek®
), interlock cable and pump fittings 70 PP7450 each
The PP3004 QuickLok and PP3006 CoolLok require either a rotary pump or high vacuum turbomolecular pumping station (recommended). The PP3005 requires a rotary pump for evacuating the vacuum isolated gas lines. 13034
Pfeiffer Duo 6 — 5 m3 with oil mist filter
24426
Options and Accessories 24429
/hr rotary vacuum pump
Pfeiffer HiCube 80 turbomolecular and diaphragm pumping system
Rapid cooling station (for PP3006 only)
Consists of a floor-mounted trolley, liquid nitrogen freezing chamber mounted into the work surface which interfaces to the cryo transfer device, connections to vacuum pump (order separately)
Pressurized (60 L) LN2 dewar. Boil-off nitrogen gas is used for cooling the stage and cold trap (PP3005 and PP3006 only)
PP3050-RWT CHE3010 Rapid Warming Tower 13296
Specimen Holders 10245
each
10246 10247 E7433
E7449-5 E7401 E7402 E7403 E7405 E7406 E7407
32816510
Sircal in-line gas dryer. Helps to reduce water content of nitrogen gas supply
Top-loading specimen shuttle for planchettes Top-loading specimen shuttle, to take a 10mm stub Top-loading specimen shuttle for rivets (vice style)
Rivet holder specimen stub, screw-down style (for use with 10246)
each
each each
each
each each each
Universal specimen stub with surface holes and slots (5 pack) each Specimen stub shuttle (spare) Aluminum (Al) stubs (10 pack) Copper (Cu) stubs (10 pack)
each each
Screw down stub for thin, hard specimens Copper (Cu) stubs with 3 x 3mm slots (5 pack) Copper (Cu) stubs with 1 x 3mm slot (5 pack) Brass rivets for fracturing liquids (100 pack)
Sputter Targets and Carbon Fiber E7400-314A Gold (Au) target 0.008" thick
each
E7400-314B Gold/palladium (Au/Pd) (80:20) target 0.2mm thick E7400-314C Platinum (Pt) target 0.008" thick E7400-314IR Iridium (Ir) target 0.008" thick E7400-314CR Chromium (Cr) target 0.3mm thick Carbon fiber cord — high purity — 1m Carbon fiber cord — high purity — 5m
91047-1 91047-5
each each each each each each
each each each each each each each
each each
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76
