HOSSFELD UNIVERSAL
®
Model No. 2 Bender HYDRAULIC POWER
Stock Hydraulic Power Recommended
ODTube ..................................1-1/4" through 2" OD
Pipe .........................................1"through 2"ID
Flat ....................................................1/2"
Round or Square Bar ...................... 3/4" through 1-1/4" dia.
Square Tube ..................................1"through 1-1/2"
Rectangular Tube .....................................Allsizes
Angle Iron ..............1/8" x 1-1/2" x 1-1/2" through 3/16" x 2" x 2"
Handrail ................................with assembled channel
H60 Hydraulic Pump
Short-run production bends and heavy bends are easy with
this state-of-the-art hydraulic pump – the only hydraulic
attachment you’ll ever need for the HOSSFELD
UNIVERSAL
®
MODEL NO. 2 Bender.
Power & Control:
With hydraulic-equipped bender and foot-control, complete
bends faster, with less work – and gauge degree of bend
better – than with manual bending. Double-action cylinder
puts 1000 psi of hydraulic assist onto the Swinging Frame –
Bend 2" Pipe or Tube up to 360°. At the touch of your foot,
cylinder returns Swinging Frame to start position while you
reset stock for additional bending.
Safe:
Safe design lets you control hydraulic action when YOU
want – Hydraulic pump runs continuously when power unit
Take a look at
is ON, giving you fast response, but you Start/Stop the
HYDRAULICS
these features –
hydraulic action – Foot Switch controls flow of hydraulic
fluid to cylinder – Removing foot from switch IMMEDIATELY
•
1000 PSI – Bender’s unique
design lets you bend with less force
stops flow of hydraulic fluid – INSTANTLY stops movement
of Swinging Frame. •
Pumps 453 cu. in. of oil per minute (approx. 2 gallons)
•
Designed to operate on a 15 amp circuit
Uses Less Force:
Bender’s unique design lets you operate safely – Rotating
•
Precision limit switch attachment for identical, repeated bends
Swing Arm uses leverage to get the job done – More lever-
•
Foot control allows use of both hands while bending – you’re
age means you can use less force – Hydraulic pump uses
free to control the stock as you bend
lower PSI than other hydraulic systems – with the same •
10-foot cord allows for foot operation in any position around
results!
bender
•
Foot switch is rated for over 1 million cycles–includes OSHA-
Compare Our Speed: approved guard designed to protect your foot when on the pedal
Bend 2" Pipe to 90° (6" radius) in under 45 seconds –
•
Separate extend/retract pedals let you control bend at all times
Bend 2" Pipe to 180° in under 2 minutes – depending on
skill of operator – Fast retraction – from full extend to full
•
Foot guard is large enough to accept steel-toed boots
retract in approximately 10 seconds. •
Liquid-filled pressure gauge allows for easy pressure reading
Production Bending:
•
Large adjustment knob allows for easy pressure adjustment
control–even with gloves on
Limit switch attaches to bending circle – stops bender at
precision point every time – great for making repeated
•
State-of-the-art pressure-balanced gear pump provides greater
efficiency and quiet operation
production bends!
•
New SAE straight thread porting and only two hose connections
Easy To Use:
helps reduce possibility of leaks on hydraulic unit
Switching back and forth between manual and power
operation is easy – Hydraulic Cylinder connects to
Swinging Frame with single pin.
SAFE WORKING CAPACITY OF HYDRAULIC POWER EQUIPMENT.
The 49405 H60 Hydraulic Power Unit is covered by a 1-year limited warranty. It is factory precision adjusted at a
maximum pressure of 1000 pounds per square inch. Operation of the Power Unit at a hydraulic pressure greater
than 1000 pounds per square inch will exceed the design working capacity of the machine and its bending tools. This could
be dangerous to the operator and will void the warranty. Only the 49405 H60 Hydraulic Pump and other hydraulic packages
supplied by us are authorized for use with the HOSSFELD UNIVERSAL
®
MODEL NO. 2 BENDER; use of other hydraulic
units may void applicable warranties.
8
www.hossfeldbender.com
Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48