HOSSFELD UNIVERSAL
®
Model No. 2 Bender FLAT AND BAR STOCK
Flat Stock – ASTM A36 Hot Rolled Mild Steel (HRMS).
Bar Stock – ASTM A36 Hot Rolled Mild Steel (HRMS).
Inside Radius (IR) – Radius bends in Flat and Bar Stock are measured from the center of the
bend to the inside edge of the stock.
Stock Capacity
Round or Square Bar ...........................Upto5/8" dia.
Flat Stock ...................................Upto3/16" x 2"
20B1 Round Cams
Form Large-Diameter Rings And Eyes in Light Stock
Bend large-diameter Rings or Eyes in light Flat or Bar Stock on top of
Bender Frame. Tooling consists of 20B2A Support Plate and Pins for
setup and 20B1 Round Cam of the desired radius. Use 11B Square
Blocks as backing blocks (included w/basic 46000 Bender package).
Support Plate and Pins
PART NO. DESCRIPTION
20186 20B2A Support Plate w/Bolt & Nut
21080 53B1 Straight Main Frame Pin, 3/4" Dia.
20B1 Round Cam mounted on 53B2 Center Pin and 20B2A Support Plate
21082 53B1B Straight Swing Frame Pin, 3/4" Dia.
forms coil in Round Bar on top of the frame. 11B Square Blocks are used as
21084 53B2 Straight Center Pin, 1" Dia.
backing blocks.
20B1 Round Cast Cams
PART NO. DIA. PART NO. DIA.
20108 2" 20136 5-1/2"
20110 2-1/4" 20138 5-3/4"
20B1
20112 2-1/2" 20140 6"
53B1
ROUND
53B2
20114 2-3/4" 20142 6-1/4"
CAM
20116 3" 20144 6-1/2"
20118 3-1/4" 20146 6-3/4"
20120 3-1/2" 20148 7"
20122 3-3/4" 20149 7-1/4"
20124 4" 20150 7-1/2"
20126 4-1/4" 20151 7-3/4"
20128 4-1/2" 20152 8"
20130 4-3/4" 20153 8-1/4"
53B1B 20B2A
20132 5" 20154 8-1/2"
20134 5-1/4" 20155 8-3/4"
20B2 Wide (2-1/2") Flat-Face Radius Blocks Stock Capacity
Form Large-Radius Bends in Wide Flat Stock –
Flat Stock .................................Upto1/2" – 2-1/2"
“The Easy Way”
Bend Flat Stock up to 2-1/2" – “The Easy Way” – in larger-radius bends.
These Radius Blocks have a flat surface suitable for bending Flat and
Bar stock and Dual Faces so each block can bend two different radii. 20B2
PART NO. IR PART NO. IR
20158 4-1/2" / 5-1/2" 20173 28" / 30"
20159 5" / 6" 20175 34" / 35"
20157 6-1/2" / 7-1/2" 20177 39" / 40"
20160 7" / 8" 20178 42" / 48"
20161 9" / 12" 20180 54" / 60"
20162 10" / 11" 20202 66" / 72"
20163 13" / 14" 20203 78" / 84"
20B2 Wide, Flat-Face Radius Blocks can also be used
20164 15" / 18" 20183 108" / 120"
with the 63B “E-Type” Clamp to bend heavy Flat stock
20167 20" / 22" 20184 228" / 240" “The Hard Way.” (See pg 31).
20169 24" / 36"
28
www.hossfeldbender.com
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48