HOSSFELD UNIVERSAL
®
Model No. 2 Bender FLAT AND BAR STOCK
Flat Stock – ASTM A36 Hot Rolled Mild Steel (HRMS).
Inside Radius (IR) – Radius bends in Flat and Bar Stock are measured from the center
of the bend to the inside edge of the stock.
Stock Capacity Inside Radius (IR)
Flat ................Upto1/2" x 1-3/4" ..............3"–120" (10 ft) IR
Handrail Capping ......Standard Handrail ....Min. recommended radius: 9" IR
51B2 Edgebend Die
Edgebend Flat Stock and Handrail – “The Hard
Way”
Bend Flat Stock and Handrail Capping edgeways–AKA “The Hard
Way”. Complete tooling consists of the 51B2 Edgebend Die Set, 50B
Outbend Master Die, 53B Wrist Pin, a 51B3 Spacer Set, and a
52B Inner Radius Block of the desired radius. The size of the Inner
Radius Block determines the radius of the bend. Inner Radius Blocks
have Dual Faces for bending two different radii.
51B2 Edgebend Die Set
20949 . . . . . . . . . . . . . . . . . . . . . 9 lbs Gross Weight
This special die (also sold on pg. 5) grips Flat Stock or Handrail 51B2-1 Edgebend Die used with 50B Master Die and Pins and 52B Inner
tightly so it bends without twisting. Radius Block edgebending Flat Stock in a wide radius.
PART NO. DESCRIPTION
20954 51B2-1 Edgebend Die
20983 51B4 Edgebend Pin (2)
51B2-1 51B4
Master Die
PART NO. DESCRIPTION
20987 50B Outbend Master Die
21078 53B Wrist Pin
The 50B Outbend Master Die and 52B Inner Radius
Blocks are used BOTH for edgebending Flat Stock and
51B3
for bending Angle Iron, Leg Out. (See pg. 39).
52B Inner Radius Blocks
PART NO. IR PART NO. IR PART NO. IR PART NO. IR
21036 3" / 3-1/2" 21043 8" / 13" 21050 21" / 23" 21057 72" / 84"
21037 4" / 5" 21044 9" / 12" 21051 22" / 26" 21058 96" / 108"
21038 4-1/2" / 5-1/2" 21045 10" / 20" 21052 25" / 27" 21059 96" / 120"
21039 5" / 7" 21046 12" / 15" 21053 28" / 32" 21060 192" / 336"
21040 6" / 9" 21047 14" / 16" 21054 30" / 36" 21061 120" / 132"
21041 7" / 8" 21048 17" / 19" 21055 42" / 48"
21042 7" / 11" 21049 18" / 24" 21056 54" / 60"
51B3 Spacer Sets (Includes 2 Short & 2 Long)
PART NO. THICKNESS PART NO. THICKNESS
20940 1/8" 20944 3/8" EXTRA-LONG 51B3 Spacer
20941 3/16" 20945 7/16"
Sets are available (Nos. 72656-72930)
20942 1/4" 20946 1/2"
for bending narrower Flat stock. These
20943 5/16"
spacers will keep the stock tight against
the 52B Inner Radius Block.
Call Factory for details.
30
www.hossfeldbender.com
Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48