Page 62
www.us-
tech.com
August, 2015
Metcal Shows New Scarab Site Cleaning System
Garden Grove, CA — Metcal is exhibiting its new Scarab Site Cleaning System (APR-2000-SCS) along with the new Solder Ball Replacement Kit and MX-HPDC dual cartridge hand piece. The Scarab ensures accurate
and repeatable cleaning of the com- ponent pad in a single user-friendly system. It redefines performance and addresses the technical demands presented by component manufac- turers today. In addition, the Scarab addresses the industry needs with an automated system capable of clean- ing component pads without contact. Reworking small chip components such as 01005, 0201, 0402 and 0602s can be difficult and require special- ized tools. Metcal has developed a technique and identified a selection of tools that enable the operator to rework these small components with repeatability and consistency. Its new solder ball placement kit meets these challenging applications. The success of conduction sol-
dering depends upon the availability and controlled flow of thermal energy into the connection during two criti- cal phases — flux activation and intermetallic bond formation. To
meet these higher thermal demands, the company has designed its new
Scarab site-cleaning system.
dual cartridge hand piece and work stand along with a series of five new
dual-shaft cartridge geometries. Contact: Metcal, 12151 Monarch
St., Garden Grove, CA 92841 % 714-230-2366
Web:
www.metcal.com
See at Nepcon South China Booth #B-1G26.
ULVAC Ships Plasma Ashing System to U.S. Gov’t Facility
Methuen, MA — ULVAC Technol - ogies, Inc. has delivered an ENVIRO- 1Xa plasma ashing/photoresist strip- ping system to a U.S. Government Research Facility, in the Washing - ton, DC area. The ENVIRO-1Xa is described as the most capable and flexible ashing system for advanced research and critical manufacturing in wafer size diameters from 4 to 8- in. (100 to 200mm). The system utilizes a high effi-
ciency downstream plasma source and can achieve ash rates >10µm/ min, with a throughput of 70+wph.
This is all achieved on a minimal footprint of 1.57m2. ULVAC Technologies, Inc. (US
subsidiary of ULVAC, Inc.) has designed and manufactured ashing systems in the United States since 1994. ULVAC Technologies, in Meth - uen, MA, is an ISO-9001 and ITAR
Certified manufacturing facility. Contact: ULVAC Technologies, Inc., 401 Griffin Brook Drive,
Methuen, MA 01844 % 978-686-7550 fax: 978-689-6300 E-mail:
sales@us.ulvac.com Web:
www.ulvac.com
KEMET Expands Automotive Capacitor Ratings
Lech, Germany — KEMET has expanded the specifications of its line of automotive grade polymer elec- trolytic capacitors. The T591 High Performance Automotive Grade Poly - mer Electrolytic Series delivers stabil- ity and endurance under harsh humidity and temperature conditions. The new extensions in clude options up to 50V for both 12V and 24V power rails. The new KO-CAPs are suitable for demanding applications where a combination of high temperature and humidity is a concern, such as in transportation, telecommunications, in dus trial and avionics. Polymer material, design and manufacturing process enhancements allow the T591 to deliver high reliability when tested to 500 hours at 85°C, with 85 percent relative humidity and while voltage is applied. The T591 KO-CAP is available
in capacitances up to 330µF and is specified for operating temperatures up to 125°C. These extensions to KEMET’s KO-CAP high performance series deliver very low ESR and
improved capacitance retention at higher frequencies allowing for miniaturization and piece count reduction. The qualification plan was based on AEC-Q200 guidelines and the products are manufactured in an ISO TS 16949 certified plant. The series is available with Production Part Approval Process (PPAP), Part Submission Warrant (PSW) and change control notification.
T591 capacitor performance expanded.
Contact: Kemet Corporation,
P.O. Box 5928, Greenville, SC 29606 % 864-963-6300
Web:
www.kemet.com.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88