September, 2021
www.us-tech.com
Page 71 ViscoTec Presents Dynamic Mixing System
KENNESAW, GA — ViscoTec is presenting its eco-DUOMIX dynamic mixing system from preeflow, as well as more of the company’s proven dispensing technology, at The Battery Show. The dispensing systems provided for manufacturers from the automotive sector, electronics industry, and medical technology are always best matched to the specific adhe- sive and the specified machine design, opti- mized for the best for performance. The problem is that there are almost
40,000 adhesives with various processing parameters. With the compact eco-DUOMIX, ViscoTec offers a dispensing solution that can mix and dispense silicones (Si), epoxy resins (EP), polyurethane (PU), polyester resin (UP) or acrylate. The biggest challenge are components
bration processes and always delivers repro- ducible results. The technical implementation also results in a lower drip potential and thus significantly lower thread drawing problems on a component, which has a positive effect on desired cycle times. This aspect is demonstrated by the meas-
urable linearity between rotor speed and out- put quantity. With the eco-DUOMIX, even if the density and viscosity of the components to be mixed vary once due to quality differences, the same dispensing result can always be achieved. Issues such as adhesive type or vis- cosity become obsolete in the machine design
phase because they can be handled flexibly and can be specified at a later point in time — basically before commissioning. To guarantee this flexibility, preeflow
uses stator and rotor materials in addition to the mixing capsule, which are almost 100 per- cent compatible with all adhesive types avail- able on the market. Contact: ViscoTec America, Inc., 1955
Vaughn Road NW, Suite 209, Kennesaw, GA 30144 % 770-422-4281 E-mail:
sales@viscotec-america.com Web:
www.viscotec-america.com
See at the Battery Show, Booth 2722
New XT H 225 ST 2x
Industrial X-ray and CT
eco-DUOMIX mixing and dispensing system.
that are difficult to mix, since they usually undergo a longer mixing process to optimally bond. Difficult to mix two-compo-
nent materials, for which purely static mixing was previously not sufficient, can now be successfully mixed. Instead of a mixing spiral, the eco-DUOMIX is equipped with a mixing capsule optimized for dead space. Materials with the same and/or different viscosities were developed and evaluated. Mixing ratios ranging from
1:1 to 10:1 is technically possible. The eco-DUOMIX is designed for speeds up to 800 RPM. Compared to the classic mixing spiral of other dispensing systems, the material consumption in the motor-driven mixing capsule is significantly lower, which has a positive effect on the overall cost, especially when using expensive materials. In terms of dispensing quan-
tities, preeflow is based on the already established systems from ViscoTec and allows a minimum dispensing quantity of up to 0.008 ml with the ecoDUOMIX, which can be applied with accu- racies of 99 percent. The dead space optimized mixing capsule used, instead of a mixing spiral, is available as a consumable and is installed directly at the outlet of the dispenser. Inside the capsule, the motor-
driven mixer ensures optimized mixing, even of components that are difficult to process, even at small volume. An exact applica- tion of the smallest sealing beads is achieved by means of a replace- able dispensing needle, which is mechanically connected to the mixing capsule. This eliminates the need for time-consuming cali-
Find out more
A unique combination of five innovative features has been incorporated into Nikon Metrology’s new 225 kV microfocus X-ray CT (computed tomography) system, the XT H 225 ST 2x. As its suffix implies, it offers twice the data acquisition speed and doubles the filament lifetime, considerably extending the system uptime.
Doubling inspection productivity raises the system’s suitability for quality control (QC) applications on the shop floor, whether in vehicle component manufacture or any serial production environment. It heralds a major increase in factory efficiency by meeting the changing requirements of today’s manufacturing sector, whereby QC is starting to drive the operation and optimization of production lines, an ethos known as Quality 4.0.
Nikon Metrology
nikonmetrology.com | +1 810 220 4360 |
Sales.NM-US@nikon.com
A unique combination of five innovative features that delivers improved usability and twice the productivity.
See at The Battery Show, Booth 2837
X-RAY AND CT INSPECTION
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100
