Figure 1: Hot-acid etching of this disc from a bearing steel billet revealed broken corners (circled in red), a lap (upper left, circled in red), several small seams, and freckle-type segregation.
Figure 2: Hot-acid etching of 9-in square disc of AISI 4142 alloy steel revealed ingot pattern and inclusion pits.
Fastener manufacturers producing alloy steel fasteners and carbon
steel fasteners in compliance to standards listed in ASTM A962 are required to produce fasteners with bars that have been macroetch tested to ASTM E381 and accepted based on the acceptance criteria in ASTM A962. The steel producer shall report the macroetch test results on the steel mill test report or mill certificate, which may subsequently be transferred to the fastener manufacturing test report. The fastener manufacturer may elect to do the macroetch testing on alloy and killed carbon steel bars or forgings independently for the purpose of compliance or verification.
Acceptance criteria: a) Ingot cast product: ASTM A962 requires the macroetch structures to be better than
Figure 3: Hot-acid etching of disc from AISI 4140 alloy steel billet revealed entrapped gas, heavy segregation, voids, and ingot pattern.
grade S2, R2, and C3 in Plate-I for ingot cast product. Etch structures with conditions of flute crack, gassy, butt tears, splash, and flakes, are not acceptable.
b) Continuous cast product: Per ASTM A962 macroetch structures with conditions of surface
Figure 4: Hot-acid etching of disc from an AISI 1050 billet revealed a “cokey” center, inclusion pits, and a dendritic pattern.
crack, diagonal crack, sub-surface crack, mid-radius crack, center crack, white band, chill structure, strong dendritic structure, weak dendritic structure, equiaxed structure, columnar structure, and mold slag are not acceptable. Conditions such as pipe or center void, center unsoundness, dark center, pin holes, and scattered porosity shall be acceptable if they are within the acceptance criteria of an ingot cast product S2, R2, and C3 or better.
Certain conditions as stated above in ingot cast and continuous cast are
Figure 5: Hot-acid etching of disc from an AISI 4145 modified alloy steel billet revealed hydrogen flakes (circled in red).
acceptable as hot working and sub-sequent reduction process or forging shall improve the macrostructure. Bars with unacceptable macroetch structures per ASTM A962 shall not be used to produce fasteners.
Conclusions:
1.Compliance to ASTM A962 requires fastener manufacturers to perform macroetch testing on alloy steel and killed carbon steel bars.
2.Macroetch test results shall be accepted or rejected based on the acceptance criteria specified in ASTM A962.
Figure 6: Hot-acid etching of a transverse disc from continuously cast AISI 1045 carbon steel revealed coarser dendrites (circled in red) at top compared to bottom, light center segregation, and halfway cracks.
Figure 7: Hot-acid etching of a transverse disc from continuously cast AISI 1008 carbon steel revealed a star-pattern open condition. (Courtesy of M. Schmidt, Bethlehem Steel Corp)
Figure 8: Hot-acid etching of this transverse section of continuously cast AISI 4140 revealed a dendritic structure, center porosity, and a band (arrow) from induction stirring. (Courtesy of B. L. Bramfitt, Bethlehem Steel Corp)
3.The test determines the internal quality or homogeneity of the steel. 4.Fastener manufacturers should report the results of the macroetch test in the fastener manufacturing certificate.
5.Fastener manufacturers can purchase the wrought steel or steel bars with results of macroetch testing as part of their purchasing contract / agreement.
6.S2, R2 and C3 are graded series in Plate-I referring to sub-surface conditions, random conditions, and center segregation.
References:
1.ASTM standard A962 “Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range” ASTM International, DOI: 10.1520/A0962_A0962M-12,
www.astm.org
2.ASTM standard E381 “Standard Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings” ASTM International, DOI: 10.1520/E0381-01R12,
www.astm.org
3.ASTM standard A193, 2012 B “Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications”, ASTM International, DOI: 10.1520/A0193_A0193M-12B,
www.astm.org
4.Metallography: Principles and Practice, George F. Vander Voort, ASM International, 1984, ISBN: 978-0-87170-672-0.
www.asminternational.org
www.fastenerandfixing.com 107
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116 |
Page 117 |
Page 118 |
Page 119 |
Page 120 |
Page 121 |
Page 122 |
Page 123 |
Page 124 |
Page 125 |
Page 126 |
Page 127 |
Page 128 |
Page 129 |
Page 130 |
Page 131 |
Page 132 |
Page 133 |
Page 134 |
Page 135 |
Page 136 |
Page 137 |
Page 138 |
Page 139 |
Page 140 |
Page 141 |
Page 142 |
Page 143 |
Page 144 |
Page 145 |
Page 146 |
Page 147 |
Page 148 |
Page 149 |
Page 150 |
Page 151 |
Page 152 |
Page 153 |
Page 154 |
Page 155 |
Page 156 |
Page 157 |
Page 158 |
Page 159 |
Page 160 |
Page 161 |
Page 162 |
Page 163 |
Page 164 |
Page 165 |
Page 166 |
Page 167 |
Page 168 |
Page 169 |
Page 170 |
Page 171 |
Page 172 |
Page 173 |
Page 174 |
Page 175 |
Page 176 |
Page 177 |
Page 178 |
Page 179 |
Page 180