TECHNICAL S2 R2 C3 or better
Do you know your bolts must meet macroetch requirements? By Sri Krishna Chimbli, Alloy & Stainless Fasteners Inc,
www.goasf.com
On several occasions fastener engineers and fastener buyers have approached the author with questions about macroetch testing and what S2 R2 C3 means. This article will provide information about macroetch testing, test results, acceptance criteria, and reporting.
A
merican Society for Testing & Materials (ASTM) A962 is a standard specification on common requirements
for bolting intended for use at any temperature from cryogenic to the creep range [1]. The consensus standards on bolting referred to ASTM A962 are ASTM A193, ASTM A194, ASTM A320, ASTM A437, ASTM A453, and ASTM A540. The general requirements covered in ASTM A962 include the steel producer to test the steel per ASTM E381, which is a standard method of macroetch testing steel bars, billets, blooms, and forgings [2]. The product specifications such as ASTM A193 require the certification to include the results of macroetch examination for carbon and alloy steels [3]. Macroetch test will provide information about the homogeneity of the steel sample. S2, R2, and C3 are conditions to a
certain degree of graded macroetch photographs of alloy and killed carbon steels. S stands for subsurface conditions, R for random conditions, and C for center segregation (listed in ASTM E381 Plate-1 standard method for rating macro etched steel). Each condition has five graded series, based on the order of severity that may be acceptable or not, depending on product specification or as agreed by the purchaser. MIL-STD-430, “Macrograph standards for steel bars, billets, and blooms,” was the first published macrostructure rating chart in 1957. This chart had four conditions with eight macroetch structures [4]. The four conditions are A: center defects, B: subsurface defects, C: ring defects, D: miscellaneous defects. Later the MIL-STD-430 was revised to show three conditions of macroetch structures with two charts; these charts were adopted by ASTM E381 in 1961. Macroetch testing according to ASTM E381 involves sampling the alloy bar/billet,
polishing, etching, and rating the structure. Sample is a disc taken from the end of the bar (after sufficient discard) by cutting the specimen transversely with saws or abrasive cut off wheels. The specimen is then polished to a smooth surface and cleaned to remove any residue or oil. To reveal the macroetch structure the specimen is hot etched using etchant, 1:1 mixture of hydrochloric acid (HCL) by volume and water as reagent. The etchant is maintained at a temperature of 160ºF to 180ºF and the specimen is etched for 15 to 30 minutes depending on the specimen size and composition. There are other etchants covered in ASTM E381 that may be used for etching as part of the procedure [2]. Specimen macroetch structure
need to be examined visually or at low magnifications to rate the structure. The rating of the structure varies depending on the casting process employed to produce the steel. Reference standard charts and conditions vary for Ingot cast or Strand cast. Continuously cast products with a reduction ratio of more than 3:1 (wrought product form) can be rated as Ingot cast products using the same reference standard charts. There are three reference standard rating charts namely Plate-I, Plate-II and Plate-III. Plate-I and Plate-II reference standard charts are used on Ingot cast products. Plate-III is used for continuously cast products. In Plate-I subsurface conditions are graded S1 to S5 with S1 being the lowest severity and S5 being the highest severity. Similarly, random conditions are graded R1 to R5 and Center segregations are graded C1 to C5. Plate-II has ungraded structures representing pattern, flute cracks, gassy, butt tears, splash, and flakes. Pattern is acceptable in any degree. Structures with flute cracks, gassy, butt tears, splash, and flakes are not acceptable. Plate-III has three types of conditions
106 Fastener + Fixing Magazine • Issue 79 January 2013
that may be observed in macroetch structures: linear conditions, circular conditions, and other conditions. A linear condition consists of surface cracks, diagonal crack, subsurface crack, mid-radius crack, and center crack. Circular conditions include pipe or center void, star crack, center unsoundness, and dark center. Other conditions are grouped as pin holes, scattered porosity, white band, chill structure, strong dendritic structure, weak dendritic structure, equiaxed structure, columnar structure, mold slag, and pattern. The acceptance criteria for macroetch testing are based on the product specifications or as agreed upon by the purchaser. Few conditions like hydrogen flakes,
cokey center segregation, inclusion pits, pattern, entrapped gas, heavy segregation, voids, dendrite structure, star pattern, centre porosity that are found in macroetch structures are shown in pictures 1 to 8 (Reprinted with permission of ASM International. All rights reserved.
www.asminternational.org) [4].
About Krishna Chimbli
Sri Krishna Chimbli has a Masters degree in Materials Engineering and Sciences (SDSM&T) and a Bachelors degree in Metallurgy and Materials Technology (JNTU). He is an active member of ASTM committees A01 and F16, and a member of ASQ. He is employed with Alloy & Stainless Fasteners Inc, supporting quality, forging, rolling, heat treatment, coating and metallurgical departments. He is also a principle auditor recognised by RABQSA in Auditing Quality Management Systems, ISO 9001 and a lead auditor.
email:
kchimbli@goasf.com 4.F11
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116 |
Page 117 |
Page 118 |
Page 119 |
Page 120 |
Page 121 |
Page 122 |
Page 123 |
Page 124 |
Page 125 |
Page 126 |
Page 127 |
Page 128 |
Page 129 |
Page 130 |
Page 131 |
Page 132 |
Page 133 |
Page 134 |
Page 135 |
Page 136 |
Page 137 |
Page 138 |
Page 139 |
Page 140 |
Page 141 |
Page 142 |
Page 143 |
Page 144 |
Page 145 |
Page 146 |
Page 147 |
Page 148 |
Page 149 |
Page 150 |
Page 151 |
Page 152 |
Page 153 |
Page 154 |
Page 155 |
Page 156 |
Page 157 |
Page 158 |
Page 159 |
Page 160 |
Page 161 |
Page 162 |
Page 163 |
Page 164 |
Page 165 |
Page 166 |
Page 167 |
Page 168 |
Page 169 |
Page 170 |
Page 171 |
Page 172 |
Page 173 |
Page 174 |
Page 175 |
Page 176 |
Page 177 |
Page 178 |
Page 179 |
Page 180