HEALTHCARE VENTILATION


A look at bringing verification ‘in house’


Dr Scott Brown, managing director and lead consultant for Health Tech Solutions, explores the benefits – including the opportunities for significant cost savings – of moving verification of specialist healthcare ventilation ‘in house’, along with the associated risks.


While ventilation is used in many areas of a hospital to provide a safe and comfortable environment for patients, staff, and visitors, some clinical areas – such as operating theatres, have additional requirements. We are fortunate that guidance is available from NHS England and NHS Improvement on specialist ventilation for healthcare premises in the form of HTM 03-01,1,2


the most recent


version having been published in 2021. This guidance comes in two parts: Part A1


specification, installation, and acceptance testing, of healthcare ventilation systems, while Part B2


deals with the concept, design, addresses the


management, operation, maintenance, and routine testing, of existing healthcare ventilation systems. This article will therefore draw primarily on information in Part B, the focus of which is the routine testing of existing healthcare ventilation systems.


A definition from the HTM Starting with a definition, and according to the HTM: “…specialised ventilation is provided to help reduce airborne infection risks in areas such as operating departments, critical care facilities, isolation rooms and primary patient treatment areas”.1


(2021a, p.1).


Hospitals use air-handling units (AHUs) and a labyrinth of ducting to provide and deliver filtered air to air terminal devices (ATDs) at a flow rate and pressure suitable for the clinical setting. All critical ventilation systems require annual verification and performance testing. In many instances this is outsourced to companies that specialise in performing this work. The cost of this work therefore has to be borne by already overburdened NHS budgets. This is surprising at first glance, as all hospitals with air- handling units will have engineering staff appointed as Competent Persons for Ventilation (CP(V)). These CP(V) engineers will have been trained in the necessary audit skills and measurement techniques, and have gained the underpinning knowledge to undertake verification of critical ventilation systems. The CP(V)s will be supported in most instances by an on-site Appointed Person (AP(V)), who will have more in-depth knowledge. This paper will explore the benefits and opportunities for cost savings by moving verification ‘in house’, along with the associated risks.


Critical systems and verification A Critical Healthcare Ventilation (CHV) system, according to HTM 03-01 (2021a, p.14),1


is defined as


follows: “Certain clinical and non-clinical areas within a healthcare establishment are considered critical to its ability to provide healthcare. Typically, ventilation


systems serving the following are considered critical… [e.g. Operating theatres, isolation facilities, Critical Care, Pharmacy aseptic preparation areas, MRI, CT…]” All critical ventilation systems require annual verification and performance testing in accordance with HTM 03-01 (2021). In an acute NHS hospital Trust, there may be upwards of 50 CHV systems (in some Trusts there may be over 100), all requiring an such testing. As part of this requirement, the inspection also demonstrates compliance with the Workplace (Health, Safety & Welfare) Regulations (1992)3


and Building Regulations (2010).4


Furthermore, performance verification is an annual requirement to comply with the provisions of the Health Act (2009).5 Advanced CHV systems, such as Ultra Clean Ventilation (UCV) systems for orthopaedic operating theatres, require specialist measurement techniques, including entrainment testing, along with specialist particle counting equipment. Furthermore, Local Extract Ventilation (LEV) systems require inspection by a Competent Person (P601 Certified), and are therefore perhaps out of the scope, at least initially,


October 2024 Health Estate Journal 113


Checking a motorised actuator damper stop.


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50  |  Page 51  |  Page 52  |  Page 53  |  Page 54  |  Page 55  |  Page 56  |  Page 57  |  Page 58  |  Page 59  |  Page 60  |  Page 61  |  Page 62  |  Page 63  |  Page 64  |  Page 65  |  Page 66  |  Page 67  |  Page 68  |  Page 69  |  Page 70  |  Page 71  |  Page 72  |  Page 73  |  Page 74  |  Page 75  |  Page 76  |  Page 77  |  Page 78  |  Page 79  |  Page 80  |  Page 81  |  Page 82  |  Page 83  |  Page 84  |  Page 85  |  Page 86  |  Page 87  |  Page 88  |  Page 89  |  Page 90  |  Page 91  |  Page 92  |  Page 93  |  Page 94  |  Page 95  |  Page 96  |  Page 97  |  Page 98  |  Page 99  |  Page 100  |  Page 101  |  Page 102  |  Page 103  |  Page 104  |  Page 105  |  Page 106  |  Page 107  |  Page 108  |  Page 109  |  Page 110  |  Page 111  |  Page 112  |  Page 113  |  Page 114  |  Page 115  |  Page 116  |  Page 117  |  Page 118  |  Page 119  |  Page 120  |  Page 121  |  Page 122  |  Page 123  |  Page 124  |  Page 125  |  Page 126  |  Page 127  |  Page 128  |  Page 129  |  Page 130  |  Page 131  |  Page 132