December, 2016
South El Monte, CA — Electro-Mech’s new SW45023 exit lamp door switch has been designed, tested and approved by Airbus Industries for installation in its A350 aircraft. The DPST illuminated switch includes several design requirements specified by Airbus, including custom PC pins for mating to the higher assembly con- nector; push-on, remain-in, and push- off switch function; 2A resistive load at 28VDC input; custom PC pin housing for protection during transit; and a case dimple for alignment with the higher assembly connector. The company’s SW45028 accom - panying lens cap has also been
Simplimatic Innovative Packaging Line
Continued from previous page Because this section of convey-
or is near a wash-down area, light amounts of overspray are a part of the environment. Eanes made sure Simplimatic would receive corro- sion-resistant cylinders, which have food-grade grease and seals incorpo- rated into the bodies. Adding the NSF-H1-rated grease was a custom feature, but did not require any extra time in delivery due to fast handling by the the team at Festo. These cylinders incorporate the company’s PPS self-adjusting air cushioning feature that provides fast setup (no adjusting screws needed) and long service life, due to the soft stop at the end of the stroke. For the changing width require -
ment, Eanes identified four position cylinders for the application. These pneumatic actuators extend or retract to four unique positions. The cylinders were also specified as corrosion-resist- ant with food-grade lubrication. Festo supplied its IP67-rated MPA-L valve manifold to control the actuators. The unit for the Simplimatic
application was a 16-station mani- fold. Dual 3/2 solenoid valves were used to control the four position cylinders. The MPA-L is a compact manifold with direct fieldbus com- munications through the Festo CPX bus node. Only one power line and one
Ethernet cable had to be run to the valve bank for a clean installation. CAD models were supplied for all key components, which streamlined fabrication for Simplimatic. Eanes provided schematics of
the pneumatic system early in the project, via the company’s Fluid - Draw software, ensuring that the functionality of the valves matched the demands of the application. “Overall, the close collaboration
with a long time supplier meant that design solutions came in faster and with sure results,” says Ray Moltchan, Simplimatic senior mech - anical engineer. “This freed up our design team to move on to new chal- lenges. It also lowered our engineer- ing overhead.” Contact: Simplimatic
Automation, 1046 W London Park Drive, Forest, VA 24551 % 800-294- 2003 or 434-385-9181 fax: 434-385- 7813 Web:
www.simplimatic.com r
TEXMAC, Inc.
3001 Stafford Drive. Charlotte, NC. 28208 Ph: 704-394-0314
www.texmac.com
TAKAYA SW45023 exit door lamp switch. TAKAYA The Flying Probe Experts TAKAYA set a NEW standard in high performance and overall test
coverage with the introduction of its Advanced Multi-Function Flying Probe Systems, the APT-1400F and the NEW APT-1400F-SL
Unprecedented Test Speed and Accuracy at the Probe Tip Architecture provides fastest and most controlled probe movement
6 Topside Flying Probes Provide Optimum Access Flexibility Four angled probes, two vertical probes (no angle)
LED Color Test Option Allows functional testing of LED “Color & Luminance”
New TOS-7F Color Camera & Vision system for AOI New high intensity dual LED light ring provides direct camera lighting
Standard Intergrated Functional Test Capability Newly designed high measurement unit Integrated 4 quadrant power supplies Frequency Measurement Capability
Programmable Function generator - Sine wave, Square wave, etc.
APT-1400F / APT-1400F-SL Multi-function Flying Probe Systems
www.us-
tech.com
Page 67 Electro-Mech Lamp Switch Approved by Airbus
approved by Airbus. The lens cap is designed to accommodate one T1 3/4 (5 mm) midget flange base lamp or LED. A lightbulb logo can also be added as an option. Lightweight and compact, the
unit weighs less than 15g (0.5 oz) and measures less than 0.75 in. (19 mm) in diameter. The switch requires approximately 1.4 in. (35.5 mm) of space behind the panel and includes PC pins for plug-in mating. The switch is rated for 2A resistive at 28 VDC and has a minimum lifespan of 200,000 cycles. Contact: Electro-Mech
Components, Inc., 1826 Floradale Avenue, South El Monte, CA 91733 % 888-442-7180 fax: 626-350-8070 E-mail:
terry@electromechcomp.com Web:
www.electromechcomp.com
NEW!
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84
