December, 2014
www.us-
tech.com
Sensoray 8-Channel Mini PCI Video Frame Grabber
Tigard, OR —Sensoray’s Model 1012, 8-channel Mini PCI-Express is a frame grabber that can simultane- ously capture eight channels of NTSC/PAL video, plus optional 8 channels of mono audio. Each video channel captures at full frame rate 30 fps (for NTSC) or 25 fps (for PAL), which results in an aggregate frame rate of up to 240 fps (for NTSC) or 200 fps (for PAL). The frame-grabber board imple-
ments a single-lane (x1) Mini PCI- Express interface that enables it to
Smart Sonic Receives NanoSlic Cleaning Certification
Canoga Park, CA — Smart Sonic, makers of the original ultrasonic stencil cleaner and 440-R SMT De- tergent, has received Certification as an approved cleaner for NanoSlic Coated Stencils. Nano coating tech- nology is gaining popularity with SMT assemblers looking to improve paste transfer, reduce underside cleaning and provide a more consis- tent board-to-board print.
be plugged into any standard Mini PCI-Express slot. All operating
All eight composite video inputs
are connected through two 16-pin con- nectors. The video capture resolution can be chosen from D1, VGA, QVGA, CIF, 4CIF, SIF, 4SIF, etc. Captured frames could be in YUYV, YUV420, or RGB555/RGB565 formats. All eight mono audio inputs can
8-channel mini PCI frame grabber.
power is supplied from the Mini PCI- Express bus and no external power supply is needed.
be connected through either of the two 16-pin connectors. The audio sampling rate could be at 8, 16, 32, 44.1, or 48kHz. Software Development Kits
(SDK) are available for Linux and Windows. The SDKs include drivers, programming samples, and compre- hensive documentation to help
users/programmers to quickly start and develop custom applications using the Model 1012. The Model 1012 is designated
for video surveillance applications. However, it can be used for all other multi-channel vision, image process- ing, and video capturing as well as recording applications. The board is not suitable for weak video signal sources and/or switching video
source applications. Contact: Sensoray, 7313 SW
Tech Center Drive, Tigard, OR 97223 % 503-684-8005 fax: 503-684- 8164 E-mail:
info@sensoray.com Web:
www.sensoray.com
Page 33
WHAT I S SCIENCE WITHOUT CARE?
Smart Sonic cleaning system certified for NanoSlic coated stencils.
Process engineers estimate that
approximately 70 percent of SMT de- fects are due to solder paste printing problems. While nano coating tech- nology is still in its infancy, the sten- cil cleaning process is well estab- lished as being instrumental in pre- venting or contributing to a misprint problem. If a stencil cleaner process is not cleaning efficiently, any amount of residual solder paste left on a stencil can dry hard as cement. Hardened deposits attract additional solder paste layers causing a “snow- ball” effect leading to blocked aper- tures, insufficient deposition of sol- der paste and other problems. The Smart Sonic Stencil Clean-
ing Process is the only stencil cleaner guaranteed to clean any type of sol- der paste from any fine-pitch stencil, verified by the U.S. EPA for environ- mental safety, user safety and clean- ing efficiency and now Certified as a
NanoSlic approved cleaner. Contact: Smart Sonic Corp.,
6724 Eton Avenue, Canoga Park, CA 91303 % 818-610-7900 E-mail:
Bill@SmartSonic.com Web:
www.SmartSonic.com or
www.SMTdetergent.com
KYZEN. COM
CLEANING is more than just getting the science right. For over 20 years our clients have seen the difference that care makes in all of our cleaning solutions. Because if we
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80