Page 84
www.us-tech.com
Test for gross and fine leaks in as little as 6 minutes.*
April, 2012
Grommets also Dampen Noise Astoria, NY — A newly developed series of Anti-Vibration Grommets specifically engineered for electrical insulation, mechanical damping and noise suppression in office or lab equipment is now available from Keystone Electronics Corp. Engineered to isolate sensitive
instrumentation from unpredictable vibration and shock, these new com- ponents have “fingers” which flex as needed to dampen unwanted noise or vibration. Incorporated are special shoulder screws to provide correct spacing which allows screws to be fully tightened down. Designed to accommodate pan-
Only NorCom optical leak technology detects both gross and fine leaks in hermetically sealed packages, this fast. Instead of using multiple technologies
and processes, you can leak test virtually any type of package with one high-speed system. The NorCom 2020™
series inspects hermetically sealed components to
MIL-STD 883 requirements either in seam seal trays, or when already mounted to circuits boards and assemblies. It automatically rejects failed devices, and reports the leak rate for each part, eliminating “divide and conquer” leak testing.
NorCom 2020™
Try it free. Send us your package samples today, for a leak test evaluation and report at no charge. *Note: Test time is dependent on package volume
www.norcomsystemsinc.com
610-592-0167 1055West Germantown Pike Norristown, PA 19403 USA
els from 0.031 to 0.125-in. (0.787 to 3.17mm) thick, these insulating anti- vibration grommets are manufac- tured from durable EPDM rubber in black or blue color. The mating, cus- tom-fitted shoulder screws are made
Keystone Anti-Vibration
of Nickel plated steel in 6-32 and M3 threads. The grommets are supplied as unassembled sets (Insulator and Screw.
Grommets dampen vibration and noise.
Contact: Keystone Electronics
Corp., 31-07 20th Road, Astoria, NY 11105-2017 % 800-221-5510 or 718-956-8900 fax: 718-956-5510 E-mail:
kec@keyelco.com Web:
www.keyelco.com
Opto Diode Intros New High-Power IR LEDs
Newbury Park, CA — Opto Diode, a division of ITW and a member of the ITW Photonics Group, is introducing the third in a series of infrared (IR) LEDs, the OD-850L. Domestically manufactured using highly reliable, liquid-phase epitaxially-grown galli- um aluminum arsenide (GaAlAs), the new high optical output IR emit- ters have a medium emission angle for optimum coverage with excellent power density. Similar to the recently intro-
duced OD850W (wide angle emis- sion) and the OD-850N (narrow angle emission) IR LEDs from the company, the new OD-850L is designed to replace the current OD- 880L (medium emission angle) device. The new emitters provide greater output power (nearly 50 per- cent more) with less degradation and higher stability than the legacy devices. In addition, the new 850nm wavelength is also better matched to photo transistors and opto integrated circuits (ICs). The new devices are especially
suitable for industrial control tasks, and are hermetically-sealed in a
standard TO-46 can that is designed with gold-plated surfaces and win- dow caps carefully welded to the case, for added durability. The LEDs can be stored or oper-
ated at temperatures ranging from - 40 to +100°C. The convenient pack-
Infrared LED.
age is especially suitable for use in optical encoders and photoelectric controls. Peak emission wavelength is 850nm, the total power output ranges from a minimum 25mW, with a typical output at 35mW, and peak
forward current at 300mA. Contact: Opto Diode Corp. 750
Mitchell Dr. Newbury Park, CA 91320 % 805-499-0335 fax: 805-499- 8108 E-mail:
sales@optodiode.com Web:
www.optodiode.com
Innovative Toolholder Extension from Schunk
Morrisville, NC — Schunk is intro- ducing its new hydraulic expansion extension TENDO-SVL. The exten- sion transforms almost every preci- sion toolholder into a highly versatile device for narrow spaces independ- ent from the spindle interface. According to the company, the pre- cise run-out, excellent vibration dampening and the internal coolant supply ensure outstanding machin- ing results and a long tool life. Because of the radial clamping
actuation, tools can even be changed in the machine. The maximum torque of the hydraulically clamped extension ensures that tools are held securely for all drilling, reaming and finish milling operations. TENDO-SVL extensions are
available in both inch (English) and metric versions.
Toolholder extensions. Contact: Schunk, Inc., 211 Kitty
Hawk Dr., Morrisville, NC 27560 % 919-572-2705 fax: 919-572-2818
E-mail:
info@us.schunk.com Web:
www.schunk.com
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96