The Embroidery Column
The importance of balance in embroidery
Madeira UK’s marketing manager, Natalie Greetham, outlines how you can establish the right balance required for consistent, reliable and attractive embroidery results.
B
alance is important in all areas of our lives and embroidery is no exception. Beautiful designs, clear logos, and amazing works of art can be produced when the right balance is struck.
Achieving optimal results requires balance across every aspect of the embroidery process because when things are ‘off balance’, problems can start to occur.
The Madeira team frequently receive calls from customers seeking advice about common embroidery problems such as puckering, threads breaking or birdnesting, where threads bunch up caught between the back of the embroidery and the needle plate. There are no quick or easy answers, there can be several culprits so you must look at the whole embroidery process to assess where things might be out of balance.
No quick or easy answers One of the fi rst things we always suggest is to change your needles. It’s surprising how many embroiderers do not have a set schedule for changing machine needles, it’s quick, inexpensive and may just do the trick!
If the problem is recurring at the same point in a design, then it might be the digitising that needs altering. It’s important to always notify your digitiser of the fabric being embroidered and the weight of thread being used because the same design may not translate successfully on all fabric types. For example, if you’re doing schoolwear or corporate logos onto multiple garments from blazers and polo shirts to hoodies and sports kit these fabrics can vary greatly in quality and stability. This is where choosing the correct weight of backing also needs to be considered. To avoid puckering the fabric must be stabilised suffi ciently, the lighter the fabric the heavier the backing needed to support and stabilise the garment. Madeira’s cut away Weblon is a go-to backing for many embroiderers, a game changer particularly for stretchy sports fabrics.
Poor tension settings can cause multiple issues such as looping, puckering, birdnesting, uneven stitches and thread breaks. For most embroidery tasks, your machine’s default tension settings will be suffi cient. However, overtime you might notice changes in the stitching that could point to tension problems. Altering tensions requires a certain amount of trial and error and will vary depending on your machine brand. A handy gadget for setting thread tensions is the TOWA digital gauge, it’s accurate, easy to use and measures both top and bobbin thread.
The amount of tension needed will differ depending on the thread type, i.e., rayon, polyester, metallic or more specialist threads such as fi re resistant or refl ective. In general, the thicker the thread the tighter the top tension should be to run well. Machine speed will also have an effect, the faster the speed, the more precise the tension settings must be. Prior to beginning any job consult with the thread manufacturer’s guidelines.
| 16 | October 2022
Guideline settings for top thread tensions: • Rayon 40 – 150gf (gram force) • Polyester 40 – 170gf • Metallic – 180gf • Thicker wool blends – 190gf
Guideline settings for bobbin tensions: • Everyday embroidery – between 22gf – 24gf • Cap embroidery – 25gf
The reverse of the same image
This Picasso image is embroidered in Polyneon Green, Madeira’s recycled polyester thread
(These numbers are only a guide and may need to be adjusted up or down depending upon your specifi c machine).
It’s best to start by adjusting the bobbin tension and remember less is more, a quarter turn at a time is recommended, turn left to loosen and right to tighten.
You’ll know the tension is perfect when you have 1/3 bobbin thread to 2/3 top thread visible underneath. More white bobbin thread visible on the back of the embroidery indicates the top tension is too tight. It’s a good idea to run a tension test on your machine periodically as tensions can alter over time. It’s also advisable to inspect the thread path and bobbin case to
confi rm your machine is threaded properly and the bobbin case is free from lint build-up, overtime this could affect tensions and the smooth running of the machine.
Always ensure you are using the correct size needle for the thread type and that the needle is inserted correctly with the groove facing the front.
By following some of these troubleshooting suggestions, you should be able to establish the right balance required for more consistent, reliable, and attractive embroidery results.
www.printwearandpromotion.co.uk
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80
