research review
QCLs with internal frequency doubling target gas sensing
Intra-cavity frequency doubling creates 3 mm QCLs from the pairing of GaInAs and AlInAs
A US TEAM has substantially improved the output power of its short wavelength of GaInAs/AlInAs quantum cascade lasers (QCLs) that feature a frequency-doubling region.
The QCL made by engineers from The University of Texas at Austin and Adtech Optics delivers room-temperature
emission at 2.95 µm, which is within the ideal wavelength range for chemical sensing and spectroscopy
applications. That’s because
the spectral range 2.5-3.5 µm contains several important molecular absorption lines, including those for methane and ammonia.
Antimonide materials can also be used to produce diode lasers, QCLs and interband cascade lasers. However, these types of device are tricky to grow and process, according to corresponding author Mikhail Belkin from The University of Texas at Austin.
His view is that a far more cost-effective platform for making mid-infrared lasers for spectroscopy is the more mature InGaAs and AlInAs materials system that is also used to make telecom lasers. Conventional QCLs made from these materials can operate in continuous- wave (CW) mode at room temperature
and span the 3.5-12 µm range. To reach the shorter wavelengths, strain compensated superlattices are used to make deeper wells and higher barriers.
However, with this conventional design it is very challenging to produce QCLs
emitting below 3.5 µm. “Although the gamma points in InGaAs and AlInAs have high energy offsets, electrons may scatter from a gamma valley in InGaAs to an X- valley in AlInAs,” explains Belkin, who adds that at certain aluminium compositions, the bangap of AlInAs is indirect.
To extend GaInAs/AlInAs QCLs to 3 µm, 40
www.compoundsemiconductor.net July 2011
the US team inserted a non-linear layer on top of the active region of the device that is tailored to have resonant optical non- linearity for second harmonic generation.
First-generation devices that were reported by the Belking group in 2010 in collaboration with teams from Princeton University and the University of Maryland delivered peak output powers below
10 µW at 3.6 µm. This has now been increased to 35 µW at 2.95 µm, using a 10 µm-wide, 3 mm-long ridge laser that was driven with 50 ns pulses at a 100 kHz
repetition rate. The latest device – which features a non-linear layer containing 28 repetitions of a multi-quantum well structure made from the pairing of In0.67
Ga0.33 As and Al0.57 Ga0.43
a room-temperature threshold current density of just 2.2 kA/cm2
value to suggest that this design is capable of yielding CW QCLs.
The increase in power of these novels lasers stemmed from improvements in material quality. Better materials were possible thanks to the collaboration of the university team with Adtech Optics, a commercial foundry that produces QCLs. “We also used strain compensated structures that allowed for more design flexibility in the non-linear layer,” adds Belkin.
Although this partnership between academia and industry led to success, there is still plenty of room for further improvement. “We had to overgrow our non-linear layer onto the Adtech Optics’ existing QCL structure, and as a result, the active region and waveguide configuration was not quite optimal for the second harmonic generation device,” explains Belkin.
The upshot of this lack of optimisation was a poor degree of overlap of the pump modes with the non-
linear section. Belkin admits that the team also made a slight mistake in its calculations of the bandstructure in the non-linear section of the device. This prevents a perfect double resonance from occurring in the QCL.
Once the team addresses these issues, it should be capable of fabricating lasers with output powers of at least 1 mW. “We then plan to process these lasers as buried heterostructure devices to demonstrate CW operation,” says Belkin. If successful, the researchers will have made devices meeting the typical output power requirements for chemical sensing and spectroscopy applications.
As – produced , a low enough
Another goal is to demonstrate external- cavity tuning of their devices, which will highlight their promise for spectroscopic applications. “Finally, we are also collaborating with Markus-Christian Amann’s group on designing second- harmonic generation lasers that can be
tuneable over 0.5-1 µm in the 2.5-4 µm spectral range,” says Belkin. “This will require additional optimisation of the non-linear section and waveguide structure that will support efficient quasi-phase- matched second harmonic generation for different pump wavelengths.”
M. Jang et. al. Electron. Lett. 47 667 (2011)
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104