Touch of the Traditional Tips and tricks for sign writing
In this month’s a touch of the traditional column from Perry Eales, owner of Perry Signs London, he talks about the tricks that he’s learned throughout his time as a sign writer and what those in the business or starting up should know.
Trick 1 Many years ago, an elderly sign writer showed me how to fold a paint cup or box that holds your paint while lettering. It’s very convenient because you can mix and thin your paint in the cup, then hold the cup by one of the tabs between your thumb and forefinger while holding the mahlstick with the same hand. The other tab can be used as a palette. Leftover vinyl paper is great for this
because it is thick and coated. If you mix up more than you need for the job, you can let it skin over and stack the boxes inside each other. You can peel the skin back and use the paint again for the next week or two. I start with a piece of paper that is
about 4.5x10in. I fold it roughly in thirds in both directions. Squeeze the ends firmly so that the box will hold its shape. Good luck.
Trick 2 We use a short, large-diameter lag bolt to seal cans of lettering paint. There’s no waste, no scum, and it’s easy to
A paper pot to hold paint and act as a palette
dispense. After each use, we shake the can upside down to seal around the bolt. Another twist on this is to drive a large nail into the lid of the can, slide the nail out,
dispense the paint, then slide it back in. You can also then thread a screw eye
into the hole. No matter what you use to plug the hole, dispensing lettering enamel through a hole in the lid is easy and minimizes waste.
Trick 3 It’s amazing how much time a simple tool can save you over the years. Twenty years ago, while I was recovering from a broken foot after falling from a ladder, a friend came up with this adjustable seat so that I could work in comfort. He welded a car jack to an angle iron frame, then I cut out a plywood seat and attached a piece of carpet. The angle base held my sign box so I
could roll the chair with my sign box to the job site, then letter a window, van door or sign. It was especially handy for sign writing, but it is helpful for vinyl application, too. I’ve been using it ever since, and it’s very handy. I also have a wooden box that I take to
Using a lag bolt to seal cans of lettering paint | 36 | July/August 2026
job sites. It is 6x12x8in. and made from overlaid plywood. It provides different seating or standing heights that suit most lower jobs. It holds my cleaning bucket, too.
www.signupdate.co.uk
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82
