July, 2015
www.us-
tech.com
Fujipoly: Self-Supporting Connectors
Carteret, NJ — Fujipoly’s Self- Supporting Sponge Connectors are suitable for connecting LCD panels
nate the need to install a separate holder. The connector is available in a multitude of widths to accommo- date LCD’s with a minimum glass lip overhang of 0.060-in. (1.5mm). The carbon-based ZE BRA
connectors can be ordered with 140, 240 or 500 conductive layers per inch and provide a current- carrying capacity of 0.050 mA per 0.040 x 0.040-in. pad. The physical char ac teristics
Self-supporting sponge connectors
to circuit boards with a very low deflection force. Each connector is made from an economical and highly reliable Zebra® core that is sand- wiched between two soft sponge sup- ports. The silicone rubber “supports” create a larger base width and elimi-
of the sponge dramatically re - duce bo w ing of the PCB due to the minimal force required to make full electrical contact. This
also makes the product suitable for severe shock and vibration applications commonly found in
hand-held devices. Contact: Fujipoly America
Corp., PO Box 119, Carteret, NJ 07008-0119 % 732-969-0100 E-mail:
info@fujipoly.com Web:
www.fujipoly.com
ESP: Clear Anti-Static Sheet
Winona, MN — Engineered Sheet Products (ESP), a division of RTP Company, has developed a thermo- plastic sheet with anti-static proper- ties inherent throughout, providing permanent protection from the dam- aging effects of static electricity and dust. Known as PermaStat™ sheet,
square) are required, ESP also offers PermaStat Plus™ sheet. The PermaStat sheets are free of
Clear, anti-static sheet for dust and static-free applications.
this compounded thermoplastic sheet has consistent surface resistivity of 109 to 1011 ohms/square, offering an excellent solution for OEMs and processors who require superior ESD protection and dust control. When higher conductivity and lower sur- face resistance (107 to 108 ohms/
carbon-based additives, and do not slough, making them suitable for dust- free environments. They are fully col- orable, and can be custom-colored to meet specific application require- ments. In addition, they contain no corrosive agents to out-gas on metal components, thereby eliminating cost- ly pre-cleaning steps in electronic assembly operations. Available in a variety of resin systems, including PP, PC, Acrylic, PETG, ABS and others, PermaStat sheets can also be cus- tomized with structural reinforce- ments, flame retardant properties, and wear additives. They are made from compounds that comply with MIL-PRF-81705D static decay specifi- cations, and can also be made from compounds that comply with UL94 V-
O flame ratings. Contact: Engineered Sheet
Products, 580 East Front St., Winona, MN 55987 % 800-432-2386 Web:
www.engineeredsheetproducts.com
Production of Ultra-Thin Material
Scarborough, ON Canada —Aismali - bar has increased production of its HTC Ultra-Thin 3.2W material with an innovative Ultra-Thin 35µ dielec- tric layer that provides higher ther- mal performance and excellent work- ing temperature. The product first launched in
2014 and demand has been steadily increasing in 2015. With a thickness of only 35 microns, this new product reduces thermal resistance down to 0.10 kcm/W (0.17 k-in./W), which offers excellent thermal dissipation conditions for high power LED assembly. The entire Cobritherm range is
100 percent proof test guaranteed. The company tests the insulation between the copper and aluminum layers under high voltage. Proof tests (high pot test) in the Cobritherm Ultra-Thin 35µ are carried out at
1000VDC. Cobritherm has been approved by top OEMs around the world with a focus on the automotive, lighting and power electronics indus- tries. It has reportedly collected excellent results in endurance test- ing and has the UL Recognition as one of the best Insulated Metal Substrates after 60,000 hours. As the dielectric layers get
reduced, testing electric insulation becomes more important. The com- pany’s regular policy for meeting its quality control standards requires proof testing (high pot test) 100 per- cent of the substrates before delivery to end users. This guarantees the dielectric insulation of the copper
and aluminum conductive layers. Contact: Aismalibar, 4-79
Milliken Blvd., Scarborough, ON M1V 1V3 Canada % 416-321-0770 fax: 416-292-3254
Aismalibar Ramps Up DXU 1001 DXU-1001
SEIKA MACHINERY, INC. HEADQUARTERS: 3528 TORRANCE BLVD., SUITE 100 TORRANCE, CA 90503 PHONE: (310) 540-7310 FAX: (310) 540-7930 E-MAIL:
INFO@SEIKAUSA.COM
WWW.MCDRY.EU
HELTORFER STRASSE 16, D-40472 DÜSELDORF PHONE: 0211-4158-0 FAX: 0211-4791428 E-MAIL:
INFO@SEIKA-GERMANY.COM
DXU 1002
WWW.MCDRY.US NORTH AMERICAN AGENT:
ATLANTA OFFICE: 1580 BOGGS ROAD #900 DULUTH, GA 30096 PHONE: (770) 446-3116 FAX: (770) 446-3118
EUROPEAN AGENT: DXU-1002 MCU-201 MCU-301 MCU-401 PROTECT YOUR IC PACKAGES FROM
HUMIDITY PROBLEMS GLOBAL DRY STORAGE LEADER FOR ELECTRONICS COMPETITIVE PRICING!
CONFORMS TO IPC/JEDEC J-STD-033C & IPC-1601
ULTRA-LOW HUMIDITY STORAGE 1%RH
Page 79
DXU
U-580 FEEDER CABINET
DXU
U-580AF FEEDER CABINET
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88