Test & measurement
long-term uptake of sustainable alternatives to kerosene-based fuel, SAF manufacturers have to demonstrate that the quality and physicochemical properties are at least comparable. To do this, there are multiple ASTM methods to satisfy.
PRINCIPAL QUALITY TESTS Lubricity is a key property for fuel. The ball on cylinder lubrication evaluation (BOCLE) adheres to ASTM D5001 and determines the lubrication function. Under controlled conditions, a steel ball is pressed against the outer surface of a rotating ring and immersed in a bath of the test fuel. After rotating the test ring for 30 minutes, the test stops and the wear scar on the test ball is measured.
Insufficient lubricity can lead to reduced fuel system efficiency, fuel pump damage and even safety risks during critical flight stages, when the engine demands optimal performance. Assessing fuel corrosivity is also important to inform fuel storage and transportation decisions. The copper corrosion test, common in the petroleum industry, adheres to ASTM D130. By placing a glass tube filled with the test fuel and a copper strip into a steel pressure vessel then warming to a stable temperature in a water bath, fuel manufacturers can simulate long-term conditions to evaluate the fuel’s ability to corrode its environment.
The analyst compares the copper strip to an ASTM colour chart to assess the relative degree of corrosion. The steel pressure vessel simulates the different conditions that the fuel would experience at various altitudes during flight. One final metric used to investigate sustainable aviation fuels’ suitability is ignition temperature testing,
conducted in adherence with ASTM E659. Unlike flash point testing, the ignition temperature is one reached without an ignition source. It is defined as the lowest temperature at which fuel will be vapourised into a gas that ignites without an external flame or ignition source.
The years leading to the 2050 production tipping point will be key for SAF manufacturers. Ensuring that their products meet the high regulatory standards set in the aviation sector is a crucial part of bringing one of the world’s highest-polluting industries into a new, more sustainable era.
SciMed
www.scimed.co.uk
Instrumentation Monthly September 2023
75
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102
