techview
Working to be Lean, Green and Energy Wise
L
ean manufacturing is a concept that engineers often tend to over-think in design and over-complicate in execution. When it comes to assembly operations this
often results in engineers stripping equipment back to the bare bones, which is almost always a huge mistake. Lean means cutting the fat, not the muscle, or as Sami Niemela, the creative director of Finland’s Nordkapp Creative Oy, put it: “Lean is about being an athlete, not a skeleton.” You may ask, “What does that have to do with energy?” The answer is, a lot, because properly thought-out and applied lean assembly operations can be very green and energy-wise without any additional investment. Here’s an example from the electronics industry. Circuit board manufacturers have a problem because the connectors that have to be installed on their products can’t fi t though the SMT (surface mount) refl ow soldering systems used to attach the electronic components. That means high- value, fully-assembled boards have to be processed through manual soldering stations where skilled technicians hand- solder the connectors in place. A single connector may have a hundred or more pins and they are often small and densely packed. Scrap rates tend to be high and costly. Compliant pin technology is a potential solution to this
problem. The idea is to press the connectors into the circuit boards rather than soldering them. The compliant pins are radially fl exible and create a mechanically and electrically stable connection to the sockets on the circuit board—with no energy-consuming solder operation required. Obviously, a press-fi t assembly process is familiar and easily automated, which should make the transition from hand-soldered assembly a no-brainer. In practice, however, it has turned out to be neither simple nor straightforward. The issues come at initial engagement between the con- nector and circuit board, where many things can go wrong. For example, what happens if a pin on the connector is bent and doesn’t line up with the hole it is to be pressed into? What if there is a mismatch and the wrong connector is going to be pressed into the board? Maybe one or more of the holes is blocked by an imperfection or solder. What if the
Glenn Nausley President Promess Inc. Brighton, MI
machine didn’t line up the connector and board properly? The outcome of these “what-ifs” is generally the same.
The press tries to force the connector and board together, destroying both—at its most expensive point in the process. These challenges can be overcome by using a sophisti- cated servo-driven electro-mechanical press with the appro- priate sensors and the right software. Promess has supplied hundreds of these systems to circuit board manufacturers for use in automated cells implementing compliant pin process. The heart of these systems is a proprietary digital signal conditioner (DSC) designed specifi cally to monitor the initial engagement between the connector and the circuit board. The DSC has a linearization algorithm built into its calibration routine that gives the press the ability to measure force accu- rately at the low end of its measuring range. This lets it moni- tor the initial engagement point precisely and the closed-loop positioning control of the system allows it to stop the press cycle before it damages the part if a problem is detected. Once past this critical stage with no problems detected, the system continues the operation until the connector is fully installed. Force and position data for each assembly is analyzed and stored for quality assurance purposes. Because the system is fully programmable, the hardware can be used to assemble a wide range of connectors to a wide range of boards simply by changing locator and gripper details. One smart piece of equipment in one cell doing a multitude of operations is the essence of lean manufacturing. Manually soldering thousands of circuit boards a day means that hundreds or more of industrial soldering stations are consuming electricity all day, every day in the plant. Much of that energy is wasted keeping the soldering iron hot while the operator is handling boards and positioning connectors. The electro-mechanical press, though, draws electricity only in the pressing operation. It uses no power when it’s idle. Moreover, SMT refl ow soldering systems can be precisely calibrated to handle the high temperatures at which today’s lead-free solders have to be applied without damaging sensi- tive electronic components. That’s not as true of the manual irons used in the traditional process.
39 — Energy Manufacturing 2015
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116 |
Page 117 |
Page 118 |
Page 119 |
Page 120 |
Page 121 |
Page 122 |
Page 123 |
Page 124 |
Page 125 |
Page 126 |
Page 127 |
Page 128 |
Page 129 |
Page 130 |
Page 131 |
Page 132 |
Page 133 |
Page 134 |
Page 135 |
Page 136 |
Page 137 |
Page 138 |
Page 139 |
Page 140 |
Page 141 |
Page 142 |
Page 143 |
Page 144 |
Page 145 |
Page 146 |
Page 147 |
Page 148 |
Page 149 |
Page 150 |
Page 151 |
Page 152 |
Page 153 |
Page 154 |
Page 155 |
Page 156 |
Page 157 |
Page 158 |
Page 159 |
Page 160 |
Page 161 |
Page 162 |
Page 163 |
Page 164 |
Page 165 |
Page 166 |
Page 167 |
Page 168 |
Page 169 |
Page 170 |
Page 171 |
Page 172 |
Page 173 |
Page 174 |
Page 175 |
Page 176 |
Page 177 |
Page 178 |
Page 179 |
Page 180 |
Page 181 |
Page 182 |
Page 183 |
Page 184 |
Page 185 |
Page 186 |
Page 187 |
Page 188 |
Page 189 |
Page 190 |
Page 191 |
Page 192 |
Page 193 |
Page 194 |
Page 195 |
Page 196 |
Page 197 |
Page 198 |
Page 199 |
Page 200 |
Page 201 |
Page 202 |
Page 203 |
Page 204 |
Page 205 |
Page 206 |
Page 207 |
Page 208 |
Page 209 |
Page 210 |
Page 211 |
Page 212 |
Page 213 |
Page 214 |
Page 215 |
Page 216 |
Page 217 |
Page 218 |
Page 219 |
Page 220 |
Page 221 |
Page 222 |
Page 223 |
Page 224