ADVANCED MANUFACTURING NOW David McHenry
DIY: Creating Through-Tool Coolant Capability a N
ew retrofi t systems make it possible to quickly, easily and cost effectively transform the standard external- coolant live tooling heads on turning machine turrets
into those with through-tool-coolant capability. And shops that have done the retrofi t are experiencing longer tool life, more effi cient chip control and less heat generation. These retrofi t systems also increase overall productivity by allowing for faster machining speeds and feeds as well as shorter cycle times. Plus, they eliminate the high initial cost of dedicated through-coolant heads along with the required routine maintenance (O-rings and lubrication) and complete system rebuilds typically needed every other year. With respect to increased machine production, through-the- tool coolant is much more effi cient than external fl ood cool- ant, which is both messy and time consuming. With each tool change, shops must interrupt machining operations to readjust fl ood coolant nozzles and, often times, getting the spray close to the cut zone proves impossible. Coolant-through tooling keeps coolant pinpointed at the cutting tool’s edge and precisely in the cut zone to evacu- ate chips and reduce heat, which ultimately shortens part machining cycle times. For example, through-the-tool coolant capability eliminates time-consuming pecking operations to pull chips out of a hole and relieves built-up heat when drilling deep holes.
Shops can also drill holes quicker in one continuous feed. And, because through-tool coolant controls heat better, it is pos- sible to machine parts at much higher speeds and feeds without the risk of excessive heat generation or premature tool wear. Maintenance-free retrofi t systems often entail few compo- nents and install within minutes. Current systems, however, require holders with internally threaded regular ER-type nuts. Fortunately though, about 50% of the manufacturing market already uses these types of holders in straight and angled live heads on turning machine turrets. Regardless of the retrofi t through-the-tool-coolant system type, any standard ER collet should work, and common collet sizes usually range from ER 16 through ER 40. The systems should handle maximum cutting speeds up to 6000 rpm and
12
AdvancedManufacturing.org | June 2015
deliver coolant pressures as high as 300 psi. Currently, special high-pressure systems that work with externally threaded nuts are in development to potentially handle coolant pressures up to 1000 psi. All retrofi ttable units incorporate some type of coolant- inducing technology. For instance, one system uses special clamping nuts that induce a tooling head’s external coolant supply into the collet holder cavity. Because this system brings the coolant in through the collet cavity, it prevents coolant from seeping back into the live tooling head’s internal compartment. Such seepage causes many of the maintenance issues associ- ated with dedicated through-coolant heads.
Coolant-through tooling keeps coolant pinpointed at the cutting tool’s edge and precisely in the cut zone to evacuate chips and reduce heat.
The special clamping nuts eliminate the need for gaskets or
O-rings, creating a virtually maintenance-free solution. Instead, the nuts use the coolant as a seal and bearing. During opera- tion, machine tool coolant fi lls a small gap between the sys- tem’s rotating component and a mating stationary nut. Once the gap is full, a liquid bearing forms and reduces friction and dissipates heat caused by system rotation. It also maintains lower operating temperatures to preserve internal components. Because the special nuts use coolant as a bearing, a machine tool’s coolant must be switched on and fl owing prior to starting a cutting tool’s rotation in the live head. Basically any level of coolant pressure will work as long as the coolant is fi ltered, and the fl ow is strong, consistent and maintained. Also, there can be no loss of pressure during system operation. Shops that would benefi t greatly from retrofi ttable alterna-
tives are those using live heads and wanting to easily and cost effectively incorporate through-the-tool coolant into their operations. Within a few minutes, these shops can add such capability and bypass the maintenance and rebuild fees often associated with dedicated through-coolant heads.
Engineering and Technical Manager REGO-FIX Tool Corporation
www.rego-fi
x.com/
MODERN MANUFACTURING PROCESSES, SOLUTIONS & STRATEGIES
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116 |
Page 117 |
Page 118 |
Page 119 |
Page 120 |
Page 121 |
Page 122 |
Page 123 |
Page 124 |
Page 125 |
Page 126 |
Page 127 |
Page 128 |
Page 129 |
Page 130 |
Page 131 |
Page 132 |
Page 133 |
Page 134 |
Page 135 |
Page 136 |
Page 137 |
Page 138 |
Page 139 |
Page 140 |
Page 141 |
Page 142 |
Page 143 |
Page 144 |
Page 145 |
Page 146 |
Page 147 |
Page 148 |
Page 149 |
Page 150 |
Page 151 |
Page 152 |
Page 153 |
Page 154 |
Page 155 |
Page 156 |
Page 157 |
Page 158 |
Page 159 |
Page 160 |
Page 161 |
Page 162 |
Page 163 |
Page 164 |
Page 165 |
Page 166 |
Page 167 |
Page 168 |
Page 169 |
Page 170 |
Page 171 |
Page 172 |
Page 173 |
Page 174 |
Page 175 |
Page 176 |
Page 177 |
Page 178 |
Page 179 |
Page 180 |
Page 181 |
Page 182 |
Page 183 |
Page 184 |
Page 185 |
Page 186 |
Page 187 |
Page 188 |
Page 189 |
Page 190 |
Page 191 |
Page 192 |
Page 193 |
Page 194 |
Page 195 |
Page 196 |
Page 197 |
Page 198 |
Page 199 |
Page 200 |
Page 201 |
Page 202 |
Page 203 |
Page 204 |
Page 205 |
Page 206 |
Page 207 |
Page 208 |
Page 209 |
Page 210 |
Page 211 |
Page 212 |
Page 213 |
Page 214 |
Page 215 |
Page 216 |
Page 217 |
Page 218 |
Page 219 |
Page 220 |
Page 221 |
Page 222 |
Page 223 |
Page 224