Internal support coils Firesleeve
TRUCK HOSE SPECIAL
222005, 222022 624
TY &
PRESSURE HOSE LOW & MEDIUM
Step 1 Step 3
Step 1 Step 3
Cut coil length. The coils Small sizes: The coil can be
Follow the appropriate hose Insert tail of band clamp
should be cut to the hose worked into the hose by
assembly instructions into hand clamping tool.
HIGH PRESSURE HOSE length, minus the nipple hand without difficulty.
through the assembly of one
intrusion. For any given hose Remove all burrs from the
end fitting. Cut firesleeve to
assembly the support coil coil prior to insertion. This
same length as hose; using
length equals the overall hose will prevent cutting of the
Firesleeve End Dip
assembly length minus the hose tube. Position the coil
(AE13702–003) dip ends of
sum of the overall lengths of midway between hose
firesleeve to a depth of three
each end fitting. (“A” dimen- ends.
quarters of an inch and allow
sions.)
to dry at room temperature.
Large sizes: With the pipe
Small size of the coil can usu- still in position, as in Step
Start firesleeve over cut end
of hose. Note: If applying
HOSE FITTINGS
ally be cut with strap cutters 2, assemble the hose over
or sheet metal shears. The the coil. With the coil fully
sleeve over PTFE or stripped
larger sizes are best cut with centered in the hose,
cover assemblies, wrap ex -
Step 4
a heavy sharp chisel or bolt remove the pipe and clamp.
posed wire with tape. Grasp Position band clamp over
cutter. With small sizes skip
sleeve and slip over the hose sleeve as shown and then
directly to Step 3.
assembly as illustrated. draw tight with hand tool.
Remove tool and cut free
end of band clamp. Repeat
on other end of assembly. To
complete, bend protruding
TUBE FITTINGS
ADAPTERS &
tail of clamp over clamp
buckle. Also repair any
scuffs or minor abrasions of
firesleeve by brush applica-
tion of End Dip
AE13702–003.
ASSEMBL ACCESSORIES &
Step 2
Compress the coil (large sizes
Step 2
Y INSTRUCTIONS
only). It is necessary to
Skin sleeve back from cut
reduce the coil diameter
end of hose enough to
slightly in order to insert it
allow assembly of second
into the hose. The easiest
end fitting. (2A)
approach is to use a length of
pipe with a notch cut in one
Then center sleeve so that
end. Clamp the plain end of
it completely covers both
EQUIPMENT HOSE ASSEMBL
the pipe in a vise, slide the
sockets. (2B)
coil over the pipe and insert
the free end of the coil into
the notched end of the pipe.
Then clamp the coil and pipe
Y firmly together. Twist the coil
to compress it prior to instal-
lation into the hose.
APPENDICIES
www.EatonProducts.com
326 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50