Standard reusable fittings with
four spiral wire hose
FC324, GH493, FC736 TY &
SPECIAL TRUCK HOSE
Step 1
Cut hose to length required Skive Tool: Use the correct
using a fine-tooth hacksaw size Eaton FT1229 hose
LOW & MEDIUM PRESSURE HOSE
or cut-off wheel. Clean cover skiving tool. Mount
Step 2
Step 3
hose bore. the tool in a vise. Push the
Sockets for hose fittings are
Liberally lubricate nipple
Hose must be stripped of
hose over the mandrel.
furnished with internal
threads and inside of hose.
its rubber cover before
Rotate the hose clockwise
annular grooved design.
Use heavy weight oil or
inserting into socket.
until it bottoms or secure
Install socket by pushing
Aeroquip 222070 hose
Locate skiving point by put-
hose in a vise and attach
hose into socket with a
assembly lube.
ting hose end next to sock-
FT1279 auger to the skive
back and forth rocking and
et as shown. Measure from
tool. Insert mandrel into the
clockwise twisting motion
hose end of socket to notch
hose and rotate clockwise
until hose bottoms on
on socket.
HIGH PRESSURE HOSE
shoulder of socket.
An alternate method is to
insert the hose in a vise.
Install socket by pushing
onto the hose with a back
and forth rocking and clock-
wise twisting motion until
the hose bottoms on the
HOSE FITTINGS
shoulder of socket.
Step 1A
Step 4
A rawhide hammer or simi-
Skive Hose until it bottoms.
Screw nipple clockwise
lar tool may be used to tap
into socket and hose.
By Hand: Cut rubber cover Machine: Use the Eaton
the socket onto the hose
Leave a
1
/
1
/
16
” clear-
around down to wire rein- S1102 cut-off and skiving
but avoid damage to inter-
32
” to
ance between nipple hex
forcement with a knife. Slit machine. Consult the own-
nal socket threads. Be sure
and socket.
lengthwise. Raise flap and ers manual. Select the cor-
not to damage hose cover
pull off with pliers. Clean rect mandrel. Turn on the
or wire reinforcement.
Recommendations for
ADAPTERS & TUBE FITTINGS
excess rubber off wire rein- machine. Put the hose over
cleaning, inspection and
forcement with wire brush the mandrel and rotate
testing are summarized on
or soft wire wheel. Do not counterclockwise.
page 318. Dis assemble in
fray or flare wire reinforce-
reverse order.
Note: when skiving, remove the rubber
ment when brushing. cover until the wire reinforcement is
exposed around the circumference of the
hose.
Thru-the-cover style reusable fittings with hose
Y INSTRUCTIONS
FC211, FC212, GH663, GH793
Place socket in vise and turn ACCESSORIES & ASSEMBL
hose into socket counter-
clockwise until it bottoms.
When assembling long
Y
lengths of hose, it may be
preferred to put hose in vise
just tight enough to prevent
from turning, and screw
Step 4 HOSE ASSEMBL
EQUIPMENT
socket onto the hose coun-
Step 1 Step 2
terclockwise until it bottoms.
Screw nipple clockwise into
socket and hose. Leave
1
/
32
”
Cut hose to length required Liberally lubricate hose
Step 3
to
1
/
16
” clearance between
using a fine tooth hacksaw cover with Aeroquip nipple hex and socket.
or cut-off machine. Clean 222070 hose assembly
Liberally lubricate nipple
Recommendations for clean-
hose bore. lube.
threads and inside of hose.
Use heavy weight oil or
ing, inspection and testing
Aeroquip 222070 hose
are summarized on page
APPENDICIES
assembly lube.
318. Dis assemble in reverse
order.www.EatonProducts.com
EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007 321
Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50