“super gem”
®
Fittings with PTFE hose
FC465, 2807, 2808
TY &
SPECIAL TRUCK HOSE
LOW & MEDIUM PRESSURE HOSE
Step 1 Step 3
Step 4
Wrap hose with masking Lubricate nipple and socket
Wrench tighten nipple hex
tape at cut-off point and cut threads. For stainless steel
until clearance with socket
square to length through fittings, use a molydisulfide
hex is
1
/
32
” or less. Tighten
taped area using a cut-off base lubricant (e.g.,
further to align corners of
machine or fine-tooth hack- Molykote* Type G), lubri-
nipple and socket hexes.
saw. Remove tape and trim cants containing chloride
Recommenda tions for
any loose wires flush with are not recommended.
cleaning, inspection and
tube stock. Any burrs on Other material combina-
testing are summarized on
the bore of the tube stock tions use standard petrole-
page 318.
HIGH PRESSURE HOSE
should be removed with a
Step 2
um lubricants. Hold the nip-
To disassemble: Unscrew
knife. Clean the hose bore.
a. Push the sleeve over the
ple with hex in vise. Push
and remove nipple; slide
Some times wire braid will
end of the tube and under
hose over nipple with twist-
socket back on hose by
tend to “neck down” on
the wire braid by hand.
ing motion until seated
tapping against flat surface;
one end and flare out, on
Complete positioning of the
against nipple chamfer.
remove sleeve with pliers.
the opposite end. This is a
sleeve by pushing the hose
Push socket forward and
New sleeves are recom-
characteristic of wire braid
end against a flat surface.
hand start threading of
mended upon reuse of HOSE FITTINGS
hose and can be used to an
Visually inspect to see that
socket to nipple.
the fitting.
advantage in the assembly
tube stock butts against the
*Molykote Type G is a registered trade-
of the “super gem” sock-
inside shoulder of the mark of the Dow Corning Corporation.
ets. Slip two sockets back
sleeve.
to back over the “necked
down” end of the hose.
b. Set the sleeve barbs into
the PTFE tube by using
assembly tool FT1038A or
working the hose bore over
ADAPTERS &
the nipple into the end of
TUBE FITTINGS
the sleeve and tube.
Assembly kit FT1081 is also
available.
Y INSTRUCTIONS
ACCESSORIES & ASSEMBL
Y
HOSE ASSEMBL
EQUIPMENT
APPENDICIES
www.EatonProducts.com
EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007 323
Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50