Silicone hose 900705 Steel protec- Step 3 900952 Plastic coil
FC252/FC352 tive coil sleeve
3a) 900705 Steel Protective
sleeve
900564 Steel protec-
Coil Sleeve
TY &
tive coil spring
The hose and the coil
should be held straight.
SPECIAL TRUCK HOSE
Taping or capping the hose
end can prevent frayed wire
ends from snagging on the
coil. Bend one end to the
coil outward to form a
slight tab to assist grasp-
ing. (Cut off or bend back
when installation is com-
Step 1
900705 sleeve
plete.) Hold the tab with
Cut hose square to length the thumb of one hand
Step 1
LOW & MEDIUM PRESSURE HOSE
required with a sharp knife. while twisting the coil
Slide extended hose clamp clockwise approximately
Follow the appropriate hose
(FF9148) over hose cover. one foot back from the coil
assembly instructions
tab. When the coil opens
through the assembly of
up sufficiently, slip the tab
both end fittings. Insert end
end to the coil over the
fitting in vise.
hose. Move the coil onto
the hose by pulling at the
Step 2
900564 spring
tab end while pushing with
Cut coil length. Coil should
HIGH PRESSURE HOSE
the other hand. Be careful
be cut to overall assembly
not to exceed the resiliency
Step 1
length “OA” minus the sum
of the coil by stretching it
of the overall length of each
Follow the appropriate too far.
end fitting. (“A” dimension).
assembly instructions
Step 2
3b) 900564 Steel Protective
through the assembly of
Coil Spring
Step 3
Push hose over beaded one end fitting. Insert one
tube. end fitting in vise.
Slide coil over hose.
Wrap the coil on the hose.
HOSE FITTINGS
Step 2
Step 4
Cut coil length. Coil should
Proceed with assembly of
be cut to overall assembly
second end fitting.
length “OA” minus the sum
of the overall length of each
end fitting. (“A” dimension).
ADAPTERS & TUBE FITTINGS
Step 3
Locate extended hose
clamp (FF9148) near the
end of hose and tighten the
clamp. Y INSTRUCTIONS
Clamps: Extended hose
clamps or clamps with a
ACCESSORIES & ASSEMBL
shoe are recommended for
securing to formed and
beaded male tube ends.
Y
CAUTION: Do not use wire
type clamps for securing
silicone hose.
Note: Use of the FF9148 hose clamp
will help prevent extrusion of the rubber
HOSE ASSEMBL
EQUIPMENT
cover through the clamp.
APPENDICIES
www.EatonProducts.com
EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007 325
Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50