Standard reusable fittings with Hi-Pac
TRUCK HOSE SPECIAL
and two wire braid hose FC195, FC310,
FC510, 2766, 2781
TY &
PRESSURE HOSE LOW & MEDIUM
Skive Tool: Use the correct
Step 1
size FT1229 hose cover
skiving tool. Mount the tool
Step 2 Step 3
Cut hose to length required
in a vise. Push the hose
HIGH PRESSURE HOSE
Put socket in vise. Lubricate nipple threads
using a fine-tooth hacksaw
over the mandrel. Rotate
or cut-off wheel.
the hose clock wise until it
Screw hose into socket coun-
and inside of hose liberally.
Clean hose bore.
bottoms or secure hose in
terclockwise until it bottoms.
Use heavy oil or Aeroquip
222070 hose assembly lube.
Hose must be stripped of
a vise and attach FT1279 When assembling long
its rub ber cover before
auger to the skive tool. lengths of hose, it may be
inserting in socket. Locate
Insert mandrel into the preferred to put hose in
skiving point by putting
hose and rotate clockwise vise just tight enough to
hose end next to socket as
until it bottoms. prevent from turning, and
shown. Measure from hose
screw socket onto the hose
HOSE FITTINGS end of socket to notch on
counterclockwise until it
socket.
bottoms.
NOTE: Sockets for hose fit-
tings in the –16, –24 and
–32 sizes are furnished
with internal annular
grooves in place of helical
grooves (all FC310 and
FC510 hose sockets are
TUBE FITTINGS
Step 4
ADAPTERS &
Machine: Use the S1102 annular grooved). Install
cut-off and skiving socket by pushing hose into
Screw nipple clockwise into
machine. Consult the own- socket with a back and
socket and hose.
Step 1A
ers manual. Select the cor- forth rocking and twisting Leave
1
/
32
” to
1
/
16
” clearance
Skive Hose:
rect mandrel. Turn on the motion until hose bottoms be tween nipple hex and
machine. Put the hose over on shoulder of socket. socket.
By Hand: Cut rubber cover
the mandrel and rotate.
around down to wire rein-
Recommendations for
ASSEMBL ACCESSORIES & Note: when skiving, remove the rubber
forcement. Slit lengthwise.
cover until the wire reinforcement is
cleaning, inspection and
Raise flap and pull off with
exposed around the circumference of
testing are summar ized on
Y INSTRUCTIONS
pliers. Clean excess rubber the hose.
page 318. Dis assemble in
off wire reinforcement with
reverse order.
wire brush or soft wire
wheel. Do not fray or flare
wire reinforcement when
brushing.
EQUIPMENT HOSE ASSEMBL
Y
APPENDICIES
www.EatonProducts.com
320 EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50