Serious debate continues in the greenkeeping profession about the differences in fineness of cut between pedestrian and ride-on mowers
and fertiliser dressings into the turf canopy. Verti-cutting has the added benefit of controlling the top surface thatch build up. It is a crucial operation in helping to reduce the ‘snakey’ ball roll that golfers encounter, especially on Poa Annua dominated swards. Personally, I never use groomers, and none of my cutting units have them installed. To have them installed means finding room for them on the unit. This is done by increasing the space between the cylinder and front roller. However, when these modifications are made, the cutting unit will lose some of its contour following capabilities of the machine, increasing the potential risk of scalping. By adding a groomer to the unit, additional weight is added. For a typical unit, it will add several kilos. This additional weight naturally puts extra pressure on the surface and, again, increases the risk of scalping. However, the main reason I avoid groomers is the extra stress that they put on the outside line or perimeter cut. If the operator could click them in and out with the flick of a switch, it wouldn't be so bad but, as this feature is not available, the operator is forced to groom the outside line with every cut, whether wanted or not. This puts an enormous amount of stress on the outside line.
Upright growth with the ball sitting on the turf and not in it
blade height.
Machines have also become more agile. I have an eighteen year old Toro 3000D. The difference between using the Toro and the John Deere 2500 is amazing. The John Deere will allow you to do a 360 degree turn on a green without leaving marks. Tight turns were just not possible with the Toro, and greens were often damaged, especially the perimeter cut. Technological advances such as these have made it possible to maintain the lower heights which I advocate with much less stress on the grass.
Grooming
Groomers on machines are very popular and all the major manufacturers now recommend them. However, grooming must never replace the need to verti-cut. As I mentioned in the Feb/Mar edition of Pitchcare, verti-cutting is crucial in achieving an upright grass plant. It allows the greenkeeper to better integrate sand
Grinding
Grinding mower units frequently is essential, whatever height you cut your greens at. The lower the cut, the more critical it is to have sharp blades. There’s nothing worse than going onto a green and seeing those white leaf tips that have been cut with a dull blade. Dull blades bruise the leaf, leaving them vulnerable to parasitic attack. I always grind my units ‘little and often’ to keep them sharp. Readily available grinders are a must in the maintaince facility for any golf course.
OVERSEEDING
Overseeding has become more and more fashionable in the last few years. Cultivars bred today have greater shoot density under close mowing and are more disease tolerant than cultivars of the past. However, seed is a lot more expensive than it used to be and careful thought is required on the timing of overseeding to maximise the chances of success. You need to consider the type of surface you want to produce but, more importantly, you need to do your homework and pick
the cultivar that is best suited to your own course. Don’t necessarily accept the sales representatives advice as gospel, do your own research. Overseeding regularly with the right cultivars will give you a greater sward density. It will also help your grass species composition. I usually overseed three times a year, in the spring, summer and autumn, at low rates, around 3g/m2
.
Again, I advocate the ‘little and often’ approach. I also only use Bent grass. At Ealing, we use Colonial Bent for budgetary reasons. However, if I had unlimited funds I would definitely be overseeding with the latest Creeping Bent cultivars.
I believe Creeping Bent to be the best
greens grass on the market. The surfaces it produces are second to none. Also, golfers love this grass, as it maintains very high shoot density under very close mowing. When I am responsible for the construction of a new green, Creeping Bent is now my preferred choice of seed.
Fescue
Whilst considering overseeding, I would like to comment on Fescue and openly share my views of it as a greens grass. Fescue is a fantastic turf grass. It has low fertility requirements and needs less maintenance than the other grasses. However, it is not a good putting green grass, especially on parkland courses and soils. It is very
temperamental and I have seen too many greenkeepers chase the fescue dream unsuccessfully. It is also prone to attack from diseases such as Dollar spot and Red-thread. More importantly, serious golfers are not impressed with its ball roll capabilities. Because it is so wiry, it can leave a very sparse surface. These thin spots often fill with Poa Annua seed heads. Fescue greens are normally cut at a height of around 5mm, so you end up with two different grasses growing at two different heights. The surfaces produced are usually slow and bumpy. I regard Fescue as a great tee and fairway grass, but not one for greens, I’m afraid.
SUMMARY
Over these three article series, I have elaborated upon several of the most important variables that allow greenkeepers to achieve and maintain a sustainable 2mm height of cut. Over recent years, techniques have changed, technologies have improved and our end-
49
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116 |
Page 117 |
Page 118 |
Page 119 |
Page 120 |
Page 121 |
Page 122 |
Page 123 |
Page 124 |
Page 125 |
Page 126 |
Page 127 |
Page 128 |
Page 129 |
Page 130 |
Page 131 |
Page 132 |
Page 133 |
Page 134 |
Page 135 |
Page 136 |
Page 137 |
Page 138 |
Page 139 |
Page 140