Morning Sky by Dee Gallimore-Perry
1 string a headpin with a 6mm swarovski vintage rose crystal bicone and make a wrapped
loop. Remove a link from a natural brass etched cable chain and connect the beaded
headpin to a 15mm natural brass jumpring.
2 Cut the head off of a 2” headpin and string a 12x6mm crystal quartz briolette, positioning
it in the center of the wire. Bead the wires above the briolette and wrap one wire around
the other. Trim the excess short wire and create a wrapped loop with the remaining wire.
Connect to the 15mm natural brass jumpring using a 4.75mm jumpring.
3 string a headpin with a 4mm swarovski amethyst crystal bicone and make a wrapped
loop, connecting it to the tail of a dragonfly connector. string an eyepin with a 10x8mm
ametrine faceted oval and make a wrapped loop. Connect the eye of the eyepin to the top
of the dragonfly connector. Connect to the 15mm natural brass jumpring.
4 string a headpin with a 4mm swarovski amethyst crystal bicone and make a wrapped
loop. string an eyepin through the top of the bar end of a toggle clasp and make a
wrapped loop. Connect the beaded headpin to the eye of the eyepin.
5 Cut a 4” length of 20 gauge bronze wire and make a wrapped loop, connecting it to the
wrapped loop on the bar end of the toggle clasp. string a 10x8mm chalcedony faceted
oval and make a wrapped loop. Repeat two more times, connecting each link, forming a
chain. Connect the last wrapped loop to the 15mm natural brass jumpring.
6 Cut a 4” length of etched cable chain and connect one end of the chain to the 15mm
natural brass jumpring and the other end of the chain to the ring end of the toggle clasp.
Repeat using a 4” length of brass cable chain, connecting one end to the first etched link
connected to the ring end of the toggle clasp.
7 Cut an 8” length of beading wire and string a crimp bead and a 4.75mm jumpring.
Thread the wire back through the crimp bead and crimp. string 13 ametrine faceted
ovals, a crimp bead, and another 4.75mm jumpring. Thread the wire back through the
crimp bead and the last few ametrine beads and crimp. Trim excess wire. Connect one
end of the beaded strand to the 15mm jumpring and the other end to the first etched link
connected to the ring end of the toggle clasp.
94
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116 |
Page 117 |
Page 118 |
Page 119 |
Page 120 |
Page 121 |
Page 122 |
Page 123 |
Page 124 |
Page 125 |
Page 126 |
Page 127 |
Page 128 |
Page 129 |
Page 130 |
Page 131 |
Page 132