INSULATION RAINSCREEN REQUIREMENTS
Architects designing rainscreen façades face increasing challenges due to new regulations, fire safety concerns, and site issues. With rainscreen specification evolving rapidly, many feel they are aiming at a moving target, as BMJ finds out.
I
nsulation is crucial to a façade’s performance, and architects need to adopt a specification approach that focusses on real-world results and anticipates future regulations. Merchants and distributors can assist by providing durable, non-combustible solutions that meet these evolving demands. Building Regulation guidance has changed dramatically in the last few years, with stricter requirements for energy efficiency and safety. Updates to Part L include tighter limiting U-values for the building fabric and require a 31% reduction in operational CO2 emissions compared to past regulations.
Gary Allen, project specification manager at Knauf Insulation, explains that these changes were made in anticipation of the incoming Future Homes Standard, which is expected to ask for a reduction in emissions of 75-80% compared with 2013 regulations.
“This means that architects need to consider ways to ensure high thermal efficiency that not only meets regulations now but will satisfy future requirements,” he says. “Regulations have also increased in complexity, with the Building Safety Act (BSA) now requiring that all buildings pass through three ‘gateways’ during the planning, design and finished construction stages to become certified as fit for use and occupation. This puts much of the responsibility for the performance of the building in the hands of the architect.” Allen says that adding to this complexity are the requirements of third parties involved in the construction process. “For example, Approved Document B requires non-combustible materials to be used in certain external wall system build-ups, such as rainscreen façades, on all residential buildings between 11m and 18m. The only exception is if a full-scale fire test to BS 8414 has been conducted. But many third parties - architects, local authorities and insurers, have already introduced blanket non- combustibility policies.”
These regulatory reforms amount to sweeping changes across the construction industry. For architects specifying rainscreen insulation, it means an increased burden of responsibility and scrutiny. This means, Allen says, that specifiers should consider using non- combustible mineral wool insulation in every rainscreen façade project and think about how the buildability of the material might impact the end result.
26
“Architects working on rainscreen façade projects must consider potential performance risks presented on site. For example, best practice for mineral wool insulation in rainscreen façades is to use a ‘rolling front’ approach, working in smaller sections to first install the insulation and then cover it with the outer panel. Prolonged exposure to wind and rain can compromise mineral wool’s performance,” he adds.
Scheduling issues
Survey data indicates that the ‘rolling front’ is only achieved approximately half the time due to scheduling issues. In 70% of cases, the sheathing insulation is left exposed for over a week – enough time for weather conditions to cause damage and compromise performance.
Allen says: “Given stringent regulatory requirements for energy efficiency and fire safety, and the requirement for the building to perform as designed to pass through all three gateways, weather damage presents a serious risk to the completion of any rainscreen façade.
“Other issues are that rigid board insulation, for example, can be particularly awkward as it won’t sit flush against a cavity unless it is perfectly uniform and flat. Boards also need to be precisely cut and taped, all of which can introduce air gaps that compromise thermal and fire safety performance.”
He says that, while responsibility for a successful installation sits in large part with the contractor, it is clear from the data that it’s all too easy for factors outside of anyone’s control to play a part in delays and installation issues. “The solution is to specify products that are resilient to prolonged weathering and are easier to install correctly, to give contractors flexibility if things don’t go precisely to plan on site. “Knauf Insulation’s Rocksilk®
RainScreen
Slab EE, for example, is the UK’s first non- combustible rainscreen sheathing insulation with an enhanced water-repellent facing, making it resilient to weathering.” It is made primarily from rock mineral wool, which is flexible and maintains close contact with the substrate, while abutting edges ‘knit’ together to minimise air gaps and maximise thermal performance.
Specification for the real world The specification of rainscreen insulation must align with the practical realities of onsite conditions to ensure optimal performance and regulatory compliance.
Allen says: “Merchants and distributors can offer expertise to ensure customers prioritise buildability and non-combustibility and can futureproof the build-up. With the right knowledge and support, customers can deliver façades that stand the test of time both in terms of functionality and compliance.” BMJ
www.buildersmerchantsjournal.net November 2024
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40
