DS-APR22-PG30_Layout 1 12/04/2022 16:58 Page 1
FEATURE
ENCLOSURES considerations specification enclosure
Russell Irvine of Hammond Electronics looks into points to consider when specifying an enclosure
I
n an ideal world, the enclosure for a new project would have been selected as early as possible in the design process. In the
real world, however, once the design is finalised the first question is normally: “What box do I need for this?” So what should you really think about when specifying an enclosure?
1. size The fundamental questions. How big are the PCB and other components? How much space is needed on external surfaces for any indicators, switches, connectors, cable entries and similar components? What space is required for board-mounted components, stand-alone electro-mechanical components or multiple horizontal boards?
2. installed environMent
For outside installation, UV stability is a potential issue for plastic enclosures. For road and rail applications, shock and vibration are likely to be a consideration. Will the ingress of dust and water be something to be considered? Are there likely to be oil and chemicals present? Is resistance to impact damage a possible problem? If so, metal enclosures typically offer better resistance than plastic ones. And are particularly high or low temperature expected?
3. enclosure Material
The main choice is between ABS and polycarbonate plastic, aluminium, stainless steel and GRP. For plastic enclosures, fire resistance is a consideration. UL94 specifies a vertical or horizontal burn, the vertical burn test being the more stringent: material will be
Protection classes for solid object protection
First figure 0 1
2 3 4 5 6 0 Scope of protection No protection.
Protection from solid objects greater than 50mm in diameter.
Protection against solid objects greater in diameter than 12.5mm.
Protection against solid objects greater in diameter than 2.5mm.
Protection against solid objects larger than 1.0mm.
Protection against the ingress of dust in harmful quantities. Dust tight.
3 DESIGN SOLUTIONS APRIL 2022
classified as V0, V1 or V2 where V0 is the highest. Polycarbonate and GRP are better for outdoor use because of their high resistance to UV embrittlement and colour fading. Aluminium enclosures are either die-cast
or extruded. Aluminium is robust, non- corrosive, lightweight, non-magnetic, easily machined, gives good impact resistance and is electrically conductive. For applications where protection against shock damage is important, where EMC is likely to be an issue or where high temperatures, dust or water are expected to be present, an aluminium enclosure is the ideal choice. Stainless steel is particularly suited for use
in pharmaceutical and food processing plants, where its cleanability, strength, and corrosion resistance are beneficial. It also has high impact resistance. GRP is light in weight, stronger than many
metals, non-magnetic, non-conductive and it is chemically inert.
4. environMental sealing
The relevant standard is IEC 60529. Typically, enclosures rated at IP54 are suitable for general purpose use. For installation in environments where dust and water are likely to be present, IP66, 67 or 68 would normally be specified. The highest rating is IP69, which gives protection against high pressure steam cleaning.
5. eMc
Die-cast or extruded aluminium will provide a level of EMC likely to be more than sufficient for
the majority of applications. Compared to other metals such as aluminium, copper and silver, stainless steel is a relatively poor attenuator, so it would not normally be chosen as the material for an EMC enclosure. Plastic enclosures are non-conductive, so they provide no EMC attenuation. If the housed equipment is likely to be susceptible to external EMC or if it will generate high levels of EM radiation, the best option is to choose an aluminium die-cast or extruded enclosure.
6. Manufacturer Modification capability
In order to make a standard enclosure suitable for a specific application, it will need to be modified. The best option is for the original manufacturer to provide a modified enclosure configured to the specific requirements of the project, so there is no need to over-order to allow for set-up and wastage quantities using third-party contractors.
specifying your enclosure
A superficial glance at any enclosure may give the impression that it is a simple box, but in reality it is the end result of a great deal of design effort and expertise to create the most useful and feature-rich housing, suitable for a use in a wide variety of applications and environments. Work with the enclosure manufacturer from an early stage in the project design cycle to tap the wealth of experience behind a standard enclosure.
Hammond Electronics T: 01256 812812
hammfg.com
Protection classes for water protection
Second figure 0 1 2 3
4 5
6 7 8
9 Scope of protection No protection Protected against vertically falling drops of water. Protection against falling water droplets up to 15° from the vertical.
Protected against direct water sprays from up to 60 degrees from the vertical.
Protected against splashing water from any direction.
Protection against low pressure 6.3mm jets of water sprayed from any angle.
Protection against powerful 12.5mm water jets from any angle. Protection against temporary immersion in water up to 1m deep.
Protection against continuous immersion in water greater than 1m in depth.
Protection against high-pressure, high-temperature jet sprays, wash-downs or steam-cleaning procedures.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58
