Water / Wastewater 13


Figure 4: Dashboard to display pressure monitoring data (© Oxford Flow, 2021)


Other indirect methods can also infer where leaks have occurred including 500 controllers for intelligent pressure management, covering more than 13% of the network. Also enhanced pressure monitoring can infer where leaks are happening. High frequency loggers are installed on critical mains and DMAs, and 1 hertz loggers elsewhere on the network.


New technologies for indirectly monitoring leakage include an integrated control system for water management incorporating a piston operated valve with automated control, pressure sensing, fl ow and water quality (Figure 3). The control unit collects signals and presents the data in a Modbus table, interacts with a high-resolution pilot actuator and uses a sophisticated algorithm to accurately control downstream pressure or fl ow rate. A setpoint can be controlled to plus or minus 0.05 bar with drift correction. Data is displayed in a dashboard where alarms can be set (Figure 4). The system can be integrated with SCADA networks. “By optimising pressure reduction, future leaks can be mitigated. Critical network performance data from the Intelligent Valve integrated with monitoring data from fl ow meters adds


Figure 5: Battery powered fl ow and temperature clip on monitoring system (© Infersens, 2021)


to understanding of fl ow in water networks and enables the identifi cation of sections of pipe network with signifi cant leaks,” adds Tristram Broadbent, Principal Engineer, Oxford Flow.


An innovative, custom designed, lightweight water turbine made using 3D printing and laser cutting, can be added to generate power for the system, either in line or on a bypass line and avoid the need for mains power. This turbine could be used as a power source for other monitoring systems.


A new real time, fully automated, fl ow and temperature monitoring system has been developed which is AI enabled, low cost and non-intrusive – it simply clips onto the outside of pipes (Figure 5). The fl ow monitoring data is viewed remotely on a dashboard or Building Management System (BMS) (Figure 6), and automated alerts can be set up to provide early warning of fl ow rates that indicate the presence of a leak. The prototype product, developed with Innovate UK funding, was trialled by customers in 2020 and the beta product was piloted in late 2021. The UK product launch is due in 2022.


Figure 6: Dashboard for remote monitoring of fl ow (© Infersens, 2021)


In the UK there is a novel opportunity for distributed real time monitoring in drinking water mains through the Fibre in Water project run by the Department of Digital, Culture, Media & Sport (DCMS). One aim of the project is to provide remote rural areas with improved access to gigabit Broadband services and 5G by installing fi bre optic cables through the existing drinking water mains network. Simultaneously, the project will also enable the modernisation of the water industry by helping solve the challenge of the removal of the public switched telephone network (PSTN) which is due between 2021-2025. The project is earmarked to help address clean water leakage. Water and telecoms are both classed as Critical National Infrastructure and experience deployment challenges, but there are potential synergies that can be exploited through this project.


There are indeed some exciting developments on the horizon for leak detection. A full SWIG workshop on Leakage will be held on 2 February 2022 if you would like to learn more about how leakage can be tackled.


Rosa Richards is an Independent Environmental Consultant specialising in water policy and monitoring. She is Programme Manager of the Sensors for Water Interest Group (SWIG), and a freelance writer of science and technology. This article is based on a SWIG/KTN Sensor Sprint webinar held on 24 November 2021. www.swig.org.uk A SWIG webinar on Leakage held on 2 February 2022 will be available to watch on a pay to view basis if you would like to learn more about how leakage can be tackled.


Author Contact Details Rosa Richards, Independent Environmental Consultant


• Bristol • Tel: 01934 830658 • Email: rosapmrichards@gmail.com • Web: https://www.linkedin.com/in/rosa-richards-7a515936/


All of our articles are online! To view and download them, visit: www.envirotech-online.com


More than just custom solutions for pressure measurement


The Keller standard product catalogue covers most areas of application for pressure measurement technology. However, there are often great benefi ts to optimising pressure sensors specifi cally for use and integration into higher-level complete systems.


Keller’s modular product design offers great fl exibility and allows customer-specifi c adaptations to be made without causing soaring costs – even for small production runs.


Keller has been carrying out countless challenging projects in the fi eld of piezoresistive pressure measurement technology for almost 50 years. Even applications that may appear trivial at fi rst glance can prove highly complex upon closer analysis. By taking the actual usage conditions of the sensor into consideration right from the outset, one can achieve major improvements in effectiveness and durability. A mutual exchange of expertise with their customers is therefore central to Keller’s success. Sharing knowledge is what enables Keller to fi nd the best sensor solution.


Keller work on a six-stage plan to create the ideal customer specifi c solution. The initial stage is to defi ne basic sensor specifi cations in order to select the appropriate components and then to assess the environmental conditions to determine the appropriate design for the intended location. Having covered the groundwork Keller then design the requested customer-specifi c solution taking all standards and laws into account, assemble the electronic modules, taking into account application-specifi c customer requests and confi gure electrical interfaces and connections. Finally, Keller will customise the product’s labelling using laser engraving or labels


The «Custom Solutions» product category on the Keller website now features everything you need to know about the possibilities and requirements for customer-specifi c product solutions involving pressure measurement technology.


More information online: ilmt.co/PL/AoDZ For More Info, email:


email: For More Info, email:


54753pr@reply-direct.com


WWW.ENVIROTECH-ONLINE.COM


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50  |  Page 51  |  Page 52  |  Page 53  |  Page 54  |  Page 55  |  Page 56