VICES ( BANGLE CLAMP, E VER, MITRE IN & RING
2. Open the knobs until the piece you’re working on slots into the opening you need, then tighten them enough to hold the piece.
3. The jig has a grooved area in it for holding wire or tube perpendicular to the depth of the jig, or for flat pieces you can put up against the straight tab for the same effect.
4. Place on your bench peg or vice depending if you’re cutting or filing your mitre vice jig and with ease take away the unwanted part of your design
Size: • Overall size: 50 x 70 x 9mm • Jaw opening size 12mm • Weight: 180g
Code J35294 Description UOM Mitre / Jewellers Jig, 45 ° & 90 ° EACH Price £24.95 Mitre / Jewellers Jig, 45 ° & 90 °
ICESB (ANGLE, CL,AMP, ENGRANGRAVER, P MITRE, P)IN & RING)
Mitre / Jewellers Jig, 45 °, 60 °, 90 °, 120 °
& 135 °
After using this tool it will be your favourite you will ever have purchased
• File/cut perfect 45 °, 60 °, 90 °, 120 ° & 135 ° angles in sheet, wire & tubes
• For metal sheets, wire and tubes etc.
• Such a handy little tool that
allows you to fairly easily create true angles on the edges or faces of work pieces.
• With a perfect angle you will get a strong solder joint, your piece will have the look of profession workmanship
• Notice on the side at the bottom of the jig two hex grub screws and two holes at the bottom of the jig. Slide a piece of metal rod with a “L” bend through this hole and lock. This technique can be used as a measuring jig in order to have your pieces the same consistent size (“L” bar/Hex key size not supplied)
• Made from hardened steel How to use:
1. The knurled knobs on the top screw up and down to loosen or tighten the jig.
2. Open the knobs until the piece you’re working on slots into the opening you need, then tighten them enough to hold the piece.
3. The jig has a grooved area in it for holding wire or tube perpendicular to the depth of the jig, or for flat pieces you can put up against the straight tab for the same effect.
4. Place on your bench peg or vice depending if you’re cutting or filing your mitre vice jig and with ease take away the unwanted part of your design
Size: • Overall size: 50 x 70 x 9mm • Jaw opening size:12mm • Weight: 180g
• Bergeon 6499
After using this tool it will be your favourite you will ever have purchased
• File/cut perfect 45 ° & 90 ° angles in sheet, wire & tubes
• For metal sheets, wire and tubes etc. • Such a handy little tool that allows you to fairly easily create true angles on the edges or faces of work pieces.
• With a perfect angle you will get a strong solder joint, your piece will have the look of profession workmanship
• Notice on the side at the bottom of the jig two hex grub screws and two holes at the bottom of the jig. Slide a piece of metal rod with a “L” bend through this hole and lock. This technique can be used as a measuring jig in order to have your pieces the same consistent size (“L” bar/Hex key size not supplied)
• Made from hardened steel • Weight: 200g
How to use:
1. The knurled knobs on the top screw up and down to loosen or tighten the jig.
2. Open the knobs until the piece you’re working on slots into the opening you need, then tighten them enough to hold the piece.
3. The jig has a grooved area in it for holding wire or tube perpendicular to the depth of the jig, or for flat pieces you can put up against the straight tab for the same effect.
4. Place on your bench peg or vice depending if you’re cutting or filing your mitre vice jig and with ease take away the unwanted part of your design
Code J52840 Description UOM Mitre / Jewellers Jig, 45 ° & 90 ° EACH Price £295.00
• Bergeon 6677 • High precision made in Switzerland • Perfect and accurate tube/wire cutting vertically • Up to 5mm capacity
How to use... • Hold the handle & slide the movable guage left to right to adjust to the desired size
• Use the measuring gauge to determine the tube/wire length size
• Lock the hexagonal nut on the back so the tube/wire does not move
1064 COUSINS TRADE SUPPLIER Code M48851 Description
Mitre / Jewellers Jig, 45 °, 60 °, 90 °, 120 ° & 135 °
UOM EACH Price £59.95
Ø5mm (Max) Tube Cutting Jig, Bergeon
Cousins Material House incredible value and best selling Joint Leveller is accurate for cutting tube/wire vertically faultlessly.
• Accurate tube/wire cutting vertically • Gives flush cuts • Can hold up to Ø5mm wire/tubing • For the jeweller, silversmith, arts, craft, contemporary jeweller, model makers and light engineers.
• Easy tool for cutting tubing or rods • Made of precision steel with a contoured sturdy handle; also comes with a removable handle for mounting the jig in a bench vice
• Can hold wire diameter from Ø0 to Ø5mm • Please note the gauge size (5) measures 0 to 30mm but the slide gauge actually extends up to 60mm
• Smallest wire length that can be cut is 1.25mm • 250 grams
How to use: • Hold the handle (6), slide left to right to adjust to the desired size (4)
• Use the measuring gauge (5) to determine the tube/ wire length size
• Lock the hexagonal nut (7) on the back so slide (4) so the tube/wire does not move
• With your thumb push down on the tube/wire with the securing/holding handle (2)
• Put your piecing saw blade into the slit (3) • You can now start saw piecing the tube/wire vertically, accurately and with a flush finish.
Code T31883 Description Ø5mm (Max) Tube Cutting Jig
UOM EACH
Price £15.95
• With your thumb push down on the tube/wire whilst securing/holding the handle
• Put your piecing saw blade into the slit • You can now start saw piecing the tube/wire vertically, accurately and with a flush finish
Details: • For the jeweller, silversmith, arts, craft, contemporary jeweller, model makers and light engineers
• Easy tool for cutting tubing or rods • Made of precision steel with a contoured sturdy handle; also comes with a removable handle for mounting the jig in a bench vice
• Capacity holding size 4.0mm • Cut possibility 90 degrees • Holds small tubing etc. for a clean flush cut • Please note this item does not have a measuring slide
Code J0886 Description
Ø5mm (Max) Tube Cutting Jig, Bergeon
UOM EACH Price £129.95
Ø5mm (Max) Tube Cutting Jig
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102
