POLISHING & FINISHING
Dimensions: • 5 1/8” long • 1 3/16” diameter • Weight 8 oz.
Note: This handpiece should not be operated at speeds faster than 35,000 rpm.
When connected to your standard Foredom motor (that runs up to 18,000 rpm), motor speed must be kept at 14,000 rpm or less (75% of full no-load speed).
We recommend using the No. 35 with the powerful TXM bench-style motor which has a built-in dial control, or the TX hang-up model with the EMX dial control for setting and holding speed to within 35,000 rpm range.
Another option is using a standard motor with an EM dial control.
Code FD35 Description
Handpiece (No.35) - Speed Increaser
No.44T - Tapered Grip for Large Collets
UOM Price EACH £115.00
Slip Joint (European) Fitting Handpieces
• Dimensions: - 5/8” long
- 1/4” diameter at tip - Weight 3.55oz.
Code FD15SJ Description
Handpiece (No.15SJ) - Hammer Action
UOM Price EACH £99.95
speed control is easier than with a foot operated control. Table top dial controls specific for use with the power chisel handpiece is available under our code
F52689 Code
F52690 F52693
F52694 F52695 F52696 F52697 F52698 Description
Chisel (Slight Curve, 9mm), Foredom A-KC503
UOM Price
Handpiece (No.50) - Power Chisel EACH £43.85 £7.50
EACH
Chisel (Curve, 8mm), Foredom A-KC504
Chisel (U Shape, 3.5mm), Foredom A-KC505
Chisel (V Shape, 5.5mm), Foredom A-KC506
Chisel (Straight End, 9mm), Foredom A-KC509
Chisel (Diagonal End, 9mm), Foredom A-KC510
EACH EACH EACH EACH EACH £7.50 £7.50 £7.50 £7.50 £7.50
• Handpiece has a reciprocating rather than rotary action and is used at low speed (0-5000 rpm) by jewelers for stone setting and decorative work.
• It requires periodic lubrication. • The hammer has a 1/32” stroke and its impact force can be adjusted from light to heavy by turning the silver knurled adjusting ring.
• It comes with an Anvil Point (FD1577) and pin for installing and tightening points.
• A Pavé Point (R15PT) for special texturing and Stylus with Carbide Tip (10212) for marking or scribing hardened steel are available separately.
• Replacement bearing available, our code F50420 No.15SJ - Hammer Action
No.18SJ - Press Quick Release
The H.44T is a collet type handpiece that accepts accessories with up to 1/4” diameter shanks. Has pre- lubricated ball bearings that require no maintenance. Comes with 3/32”, 1/8” and 1/4” collets, pin and wrench for changing collets and accessories.
Dimensions: • 5 5/8” Long • 1” diameter (center), 3/4” diameter (taper) • Weight 5.85 oz.
Other size collets are available separately or in Collet Set FDHP440 (HP440)
Code FD44T Description
Handpiece (No.44T) - Tapered Grip for Large Collets
UOM Price EACH £41.50
Large range of slip joint headpieces available and also see our listings for spare collets, hammer heads etc.
A slip joint fitting is widely used by European manufactures. Simply press the lever pull the hand piece and you will find it easily detaches/ mounts.
No.50 - Power Chisel & Chisels
In stock now we have a slip joint pendant drill (code FDSR2CE) so if you prefer this type of fitting all you have to do is choose a hand piece for your criteria
One can appreciate Foredom’s high standard of quality in the industry. Foredom slip joint hand pieces are one of the market leaders in this field across Europe.
No.8SJ - Slim with Chuck Guard
Foredom’s Chisel Handpiece gives a power assist to carving projects in all types of wood, plastic, and plaster. This handpiece has a contoured body design that features a rugged plastic barrel and tapered aluminium ends.
• Optimum Speed Range: 3,000-10,000rpm • Maximum Operating Speed: 18,000rpm • For use with any TX, LX or SR motors • Chisel Handpiece must be used only in the forward motor direction
• Key tip (USA) fitting • Selection of chisels available separately
Dimensions: • 150mm long • Ø26mm diameter • 130g
Maintenance: After every 200 hours of use you should clean and lubricate this handpiece. The old grease must be cleaned off of the interior cam chamber and replaced with new lubricant.
Operating Tip: Using the chisel handpiece with a dial 982 COUSINS TRADE SUPPLIER
• Foredom’s most popular Quick Change handpiece features a super slim grip and lever action that opens and closes the collet.
• It has pre-lubricated ball bearings that do not require lubrication.
• Removing and cleaning of the precision collet is easy to do.
• Collet: FDHP703
• Dimensions: - 6 3/8” long - 19/32” diameter - Weight 3.6 oz.
Tip: When you go to pull the bur out, press the lever and press bur IN slightly before removing. This makes
removing the burr much easier! Code
Description FD18SJ
Handpiece (No.18SJ) - Press Quick Release
UOM Price EACH £99.95
No.20SJ - Lever Quick Release
• Comes with 2.35mm (3/32”) and 3mm collets, and chuck wrench set.
• Collet-type chuck handpiece with slim design and chuck guard sleeve that protects fingers when working up close and slides back when changing collets and accessories.
• Comes with 3/32” (2.35mm) and 1/8” (3.18mm) collets, and set of chuck wrenches.
• Other fractional and metric collets are available separately, and in Collet Set 600.
• Dimensions - 5 ½” long - 5/8” diameter - Weight 3.5 oz.
Code FD8SJ Description
Handpiece (No.8SJ) - Slim with Chuck Guard
UOM Price EACH £59.95
• The No. 20SJ has a molded plastic front grip with tapered sides for easy and close handling
• It has pre-lubricated ball bearings that do not require lubrication
Dimensions • 5 1/2” long • 5 1/64” diameter • Weight 5.3 oz.
The collet in this handpiece can be adjusted if the hold on a bur shank is not secure, please see the video link above.
Replacement collet: FDHP31008 Code
Description FD20SJ
Handpiece (No.20SJ) - Lever Quick Release
UOM Price EACH £63.95
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102
