Spray Applied Insulation -
High performance heat loss mitigation
Paddy Leighton, UK Director for Spray Foam insulation specialists Icynene, looks at heat loss in buildings and how new, high performance insulation systems can improve comfort levels in retrofit and new build applications.
When Britain began its post war building boom, coal was king and energy was relatively cheap, so little thought was given to heat loss and few buildings were constructed with any meaningful level of insulation.
Seventy years on and the world is very different. With sky-high heating costs and a greater focus on the need to reduce energy consumption, builders, landlords and homeowners all take the insulation of their properties much more seriously.
But before we look at insulation it’s important to understand what’s involved. Insulation in a building is introduced to provide resistance to heat flow. The more heat flow resistance the insulation provides, the lower the likely heating (and cooling) costs. Good levels of insulation not only reduce heating and cooling costs, but also improve comfort.
HOW INSULATION WORKS
To understand how insulation works it helps to understand heat flow, which involves three basic mechanisms - conduction, convection, and radiation.
Conduction is the way heat moves through materials, such as when a spoon placed in a hot cup of coffee conducts heat through its handle to your hand.
Convection is the way heat circulates through liquids and gases, and is why lighter, warmer air rises, and cooler, denser air sinks.
Radiant heat travels in a straight line and heats anything solid in its path that absorbs its energy - think about sitting in front of a roaring open fire and how you feel warm on the side facing the fire but less so on the other!
Insulation materials work by slowing conductive heat flow and to a lesser extent, convective heat flow. Regardless of the mechanism, heat flows from warmer to cooler areas until there is no longer a temperature difference. In a typical home, this means that in winter, heat flows directly from all heated living spaces to adjacent unheated roof voids, garages, cellars and particularly to the outdoors. Heat flow will also move indirectly through interior ceilings, walls, and floors, wherever there is a difference in temperature.
To maintain comfort, the heat loss in the winter must be replaced by heat from a central heating system or other means. Adequate levels of insulation will decrease this heat loss by providing an effective resistance to the conductive flow of heat.
28
Foams are applied as a two-component mixture that expands 100-fold within seconds of application, sealing all gaps, service holes and hard to reach voids.
HOW CAN WE INSULATE EFFECTIVELY?
Retrospective insulation - that which is fitted after construction of the building - has traditionally taken the form of thick layers of glass or mineral fibre placed between rafters in the roof void, or blown in cavity wall insulation such as styrene beads or mineral wool.
These forms of insulation work well but they do not significantly address the crucial factor of preventing convective heat loss.
In the UK, U values are the measure of insulation’s ability to limit conductive heat flow - the lower the U value the better the resistance to heat loss. However, it should be noted that up to 40% of a building’s heat loss can be attributed to air leakage.
Moisture vapour in the air within a building carries heat, and moist humid air can support up to 4000 times more hat energy than dry air. As air leaks out of a building it carries with it this moisture vapour and with it, heat.
Therefore, the best way to increase the energy efficiency of a building is not merely to reduce U values as required by Building Regs, but rather to combine U value reduction with an air barrier - creating a ‘sealed box’ effect to reduce air (and heat) leakage to a minimum. (*Footnote)
SPRAY APPLIED INSULATION
Traditional forms of insulation are relatively inefficient in sealing the box, in that they cannot completely fill all voids or seal the interface between the insulation and the building structure. Nor can they cope with small structural movements which will often lead to air gaps, particularly in difficult to treat situations where access is poor and/or when voids are of complex geometry. This can lead to cold bridging and thermal by- pass, with the consequent risk of localised condensation and inevitable dampness.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56
