BRUSHCAT RO T A RY CU T T ER 23
DOUBLE-EDGED BLADES Switch the hydraulic hoses at the drive motor for bi-directional rotation that increases overall blade life.
EASY-TO-OPEN TOP COVERS Gain instant access to the drive components and maintenance areas and save time on maintenance.
FLOTATION LINKAGE Allows the deck to float fore and aft, left and right over ground contours, keeping the Brushcat rotary cutter in contact with the surface for optimum performance.
FRONT ROLLERS (standard) Allows the Brushcat rotary cutter to better traverse uneven terrain, minimizing skips while reducing operator fatigue.
REAR TAPERED ROLLER Helps improve deck flotation. Helps contain debris within deck.
PATENTED BLADE SHUT-OFF Stops blade rotation when the Brushcat rotary cutter is raised off the ground.
FRONT SAFETY CHAINS Help contain debris within deck.
HYDRAULIC PRESSURE GAUGE Visible from the operator seat, the gauge indicates the operating pressure range of the loader. Pressure gauge ranges are signified by green, yellow and red color codes – allowing operators to monitor and maintain optimal carrier travel speed and improve efficiency.
VELOCITY FUSE If the hydraulic capacity of the motor is exceeded, the velocity fuse will shut off the hydraulic flow to the cutter, limiting potential damage and providing a definite uptime advantage.
BOB-TACH MOUNTING SYSTEM Quickly, easily connect and disconnect the Brushcat rotary cutter with the Bob-Tach mounting system. Spend less time on attachment changes and more time on the job.
MEETS SAE AND ASAE STANDARDS Bobcat Brushcat rotary cutters comply with SAE J232 and ASAE S483 standards for industrial rotary cutters.
BRUSH S AW brush-clearing jobs.
saplings up to 3-inches in size
Scan the code to watch the Brushcat in action.
bobcat.com/brushcat
Cut away brush & clear small trees.
Clear the way with the Bobcat brush saw attachment. This heavy-duty attachment saws off trees flush with the ground or even a little below the surface. Position the boom manually in up to three positions – center, or 12-degrees left or right – to operate with excellent visibility of the cutting, clearing action.
Operating Weight
Width Length Height
Cutting Wheel Diameter Maximum Wheel Tip Speed Number of Teeth
Degree of Angle (right or left) Hydraulic Flow
590 lb. (268 kg)
48.0 in. (1219 mm) 85.0 in. (2159 mm) 29.5 in. (750 mm) 28.5 in. (724 mm)
2985 ft./min. (910 m/min.) @ 22gpm 16
12 deg. 15-24 gpm (57-91 L/min.)
*Note: A Special Applications Kit must be installed on the
Approved Machines: Skid-Steer Loader, Compact Track Loader, All-Wheel Steer Loader
and grass- lands
and utility line rights-of-way
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96