Looking down into the box (above left), the hems and elastic cord on the inside ends of the sleeves can be seen. Also shown
sandblasting booth online. When I was finally ready to build my own sand- blasting booth those photos had been removed. My booth follows many of the general ideas posted by this chat list member, and I thank him for his ideas and inspiration.
Building the booth
I started my project to build a suitable booth with a 12″×18″×12″ high plastic storage box from my local hardware store. Mine was marketed by Sterilite®, although there are many other sources. Besides the general size, I was also looking for a storage box with a tight-fitting lid with clips on both ends to hold the lid relatively tightly to the box, rather than a lid designed to simply drop into a groove around the perimeter of the box.
My first task was to add a “viewport” in the lid of the box since it was frosted plastic. I cut a 6″×9″ opening in the lid with a box cutter, then covered it with a 7″×10″ sheet of ¹/₈″ sheet acrylic screwed to the inside of the lid with ¹/₄″−thick weather stripping foam tape between the lid and the acrylic to seal the opening. I next cut a pair of 4¹/₄″ diameter holes
(8″ center to center) in the front of the box for my arms. I first checked the di- ameter by cutting a hole in a piece of scrap cardboard to make sure they were large enough for easy access to the box. My wife Jacque then cut the sleeves off of an old “railroad motif” shirt (just a co- incidence to the project) and added a hem to the “hand” ends of each sleeve. Elastic cord was fed through the hems, and the ends were captured by cord locks from a fabric store. The elastic cord and locks allow me to close the ends enough to prevent blown abrasive from entering the sleeves while still letting me get my hands into the box.
I next cut a pair of rings from ¹/₈″ hob- RAILROAD MODEL CRAFTSMAN
(above right) are the shop vacuum connection, a pencil sand- blaster, a container of abrasive and a foot pedal air valve.
by plywood to use to attach the large ends of the sleeves to the box. The holes in these rings are the same size as the holes in the box; the outside diameter is around one inch larger. My original thought was to glue the upper ends of the sleeves to the plywood rings, which could then be screwed to the outside of the box to hold the sleeves in place. Instead, my wife and I decided to add hems to the upper ends of the sleeves along with some elastic cord and cord locks similar to the other ends of the sleeves. The wood rings were loosely at- tached to the box with four ¹/₂″ long screws and nuts, and the upper ends of the sleeves were stretched over the wood rings.
Tightening locked the sleeves in place.
Since I’m right-handed, I drilled a hole near the bottom of the box on the right side for the hose attached to my pencil sandblaster.
Even though the pencil sandblaster utilizes a small amount of air, I felt I should include a way to let air get out of the booth while I was sandblasting. Although air could simply leak out of the “sleeves” while sandblasting, that might also mean abrasive dust was also leaking out. If you want to recycle the abrasive, a simple opening equipped with some sort of air filter could be added to the box. However, I was more concerned about controlling dust from the box and making sure that visibility of the item being sandblasted wasn’t being compromised by dust in the booth, so I added a connection for my shop vacuum to the back right corner using a utility vacuum nozzle. After cutting a hole for the nozzle, I bolted it to the back of the box and patched the entrance hole with construction adhe- sive. If you want to recycle the abra- sive, you might think about installing the outlet high in the box. That might keep the air clear (so that you can see
the screws
your progress) while also not pulling the abrasive out of the box.
Sandblaster and other equipment My pencil sandblaster is a Model BB100 Bottle Blaster purchased from the Cyclone Manufacturing Company (
www.cycloneblasters.com). These they cost around $90.00 to $120.00 from on- line distributors. In addition to the sandblaster, you will need an air com- pressor which puts out 80 to 90 p.s.i. The pencil sandblaster is mechanically very simple, pulling abrasive directly from a refillable 20-ounce container of abrasive. It took me a little while to fig- ure out that the hole in the brass tube/ handle had to be covered for the sand- blaster to work. A rubber grommet is pro- vided to cover the hole, or you can use a fingertip and manually adjust the output flow. The latter option might be worth considering if you bypass the foot-operat- ed air valve. I fitted my air valve with a quick-coupler to make it simple to con- nect it to the hose on my air compressor. I use Paasche Air Eraser Compound (AEX-5) for my sandblasting. It is an aluminum oxide material. I have found that it works fine on brass, but softer abrasives are also available. Paasche sells sandblasting compounds directly at the site,
www.paascheairbrush.com, under Etching and Striping Tools. Using the outfit is fairly simple. I wear latex gloves (available from Costco in 150-count boxes) while sandblasting and hold the model in one hand and the sandblaster in the other, keeping the tip ¹/₄″ or so from the part being prepped. Keep the sandblaster moving just like when airbrushing and watch your progress. Only one or two passes are needed to completely prepare a part. Sandblasting is a great way to clean
and give metal parts some “tooth” prior to painting. This sandblast booth makes this an quick and easy process.
47
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100