The DTG Column
Fibrillation and fibres – What is it and how to get rid of them
In this month’s article Colin Marsh, managing director of Resolute DTG, explores fibres and fibrillation. He details the most common types of related problems and how to combat them.
W
hen printing a T shirt with any DTG process the surface you print onto will determine the end result. Fibres and fibrillation can cause a range of quality issues, some not visible to the naked eye until the garments are washed. The two (fibres and fibrillation) must not be confused as they give different results.
Fibres Letʼs start with the symptoms made by fibres. The picture shows the fibres showing in the image that would not be visible before printing. This is common when the actual cotton fibre has snapped in the manufacture process and is allowed to pop up. DTG ink is very thin so the fibres sticking up will not be pushed down by the white ink and actually shows up worse after the CMYK ink has been printed on top of the white.
fall off also take the ink printed onto them at the same time, this mimics fading of the ink, this is very often not the case.
The print will look faded because the missing fibres are now holes in the print reducing the visual density of the image. Combating this kind of fibrillation is again dependant on the pre-treatment process and the type of solution and process used.
Before pre-treatment
Fibrilation symptons
● Pre-press the garment for approximately 20 seconds before
After pre-treatment immediately press again for
approximately 30 seconds. ● The pre-treatment must be dry before
removing the silicone paper. ● Check this by sliding the paper off, do
Print with fibres showing
When printing with white ink certain methods of pre-treatment are better at dealing with fibres than others. The before and after pictures show the surface fibres standing up, after pre-treatment they no longer show and the fabric will now print correctly. In order to achieve this, the following procedure should help on any DTG
system. ● Pre-press the garment for approximately 20 seconds before
pre-treating. ● Use medium pressure and a clean
sheet of silicone paper. ● Now pre-treat the garment and
| 54 | June 2017
not peel or lift upwards. ● If it will not slide off with no
resistance it is not dry. ● Now print and cure as normal.
Fibrillation – what is it and what does it do
Stray fibres from the manufacturing process are not part of the complete length of woven cotton. These fibres can get dislodged in the wash cycle and can cause some strange fading or peeling problems. As the fibres dislodge in the wash they fall off and disappear.
Not too much to worry about as there are literally millions of fibres in a single T shirt so the fabric will not be affected by this but the print will. The fibres that
pre-treating. ● Use medium pressure and a clean
sheet of silicone paper. ● Now pre-treat the garment with 50% the normal amount, press again for
approximately 20 seconds. ● The pre-treatment must be dry before
removing the silicone paper. ● Check this by sliding the paper off, do
not peel or lift upwards. ● Repeat the above process. ● The pre-treatment must be dry before
removing the silicone paper. ● Check this by sliding the paper off, do
not peel or lift upwards. ● If it will not slide off with no
resistance it is not dry. ● Now print and cure as normal.
Splitting the pre-treatment process into two applications allows the second application to bind the already coated loose fibres to the rest of the cotton strands. This obviously takes a little longer but allows cheaper shirts to be used at the same time as generating better wash results and longevity for the print.
www.printwearandpromotion.co.uk
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76
