search.noResults

search.searching

note.createNoteMessage

search.noResults

search.searching

orderForm.title

orderForm.productCode
orderForm.description
orderForm.quantity
orderForm.itemPrice
orderForm.price
orderForm.totalPrice
orderForm.deliveryDetails.billingAddress
orderForm.deliveryDetails.deliveryAddress
orderForm.noItems
BOILER


COMMERCIAL SUPPLEMENT


Peace of mind S


ervicing and commissioning commercial heating systems means every day can offer a challenge which wants to be solved, especially due to the scope of commercial projects. Hands-on in- depth product knowledge and even extended warranty terms (manufacturer-dependent) can be two of the advantages of using a manufacturer’s service engineer for commissioning. The former is also the reason why some project specifications ask for the commissioning to be carried out by the manufacturer. But what are the benefits of commissioning itself and what does it involve?


The whole system


A variety of elements come into play for a heating system to run the way it’s supposed to – gas pipes/supply, pumps, ventilation, flueing, the boiler etc. During a commissioning job, we’re not only looking at boilers and water heaters but rather the system as a whole to see if it is actually possible and safe for the boiler to be fired. Once I was on a job at a very well- known site in London. I was shocked when I discovered they had no safety valves on their boilers, which could easily lead to an explosion causing harm to occupants of the building. Would you feel confident to drive a new car that hasn’t been tested?


All in a log book Before firing the boiler, I carry out pre- commissioning checks, such as if there’s water in it – firing a dry boiler can be quite dangerous – and if the chimney is connected. Following a commissioning


procedure, I document everything assessed and measured in the plant room. For the boiler system, it’s about making sure the pipe connections are installed as per the instruction manual, checking safety mechanisms are fitted (such as safety valves) and the system pressure is in a normal


S12 September 2017


Dave Ward of Hamworthy Heating (below) argues that commissioning leads to efficiency and benefits end users, contractors and manufacturers


Dave Ward, service engineer at Hamworthy Heating, explains what a commissioning job entails and why it’s worth considering not just in terms of efficiency, but also why it benefits end users, contractors and manufacturers alike


I’m also making sure the gas supply is sufficient. Despite calculations when the boilers are fitted, it might not be big enough, especially where an older system has been inherited but not updated to accommodate new boilers or water heaters.


It’s a matter of education


Sometimes, however, I visit a site and there are so many issues that need to be rectified before the boiler can be fired. In these cases, I will write up a sheet with advisory notes for the customer to resolve the problems before I can carry on with the commissioning job. On a servicing job at a premium supermarket chain I once encountered a boiler with 25 fault messages caused by the store manager pushing the reset button. In those cases, it really is a matter of educating the customer.


The overall package


range. Next, the flue system is checked (sizing, no spillage) and of course the gas. It’s vital the supply is sufficient and not undersized to ensure the boiler can run on it. To test the safety functions are working, I stop the gas supply which should produce a fault code telling me there is no gas supply. Once the boiler is fired, I check the flue-gas to see if it’s firing correctly. Incomplete combustion would mean it isn’t and lead to the formation of dangerous carbon monoxide. But that’s just one of several checks I carry out.


Gas safety


There are of course legal requirements for gas work, probably the most important being The Gas Safety (Installation and Use) Regulations 1998.


As a gas engineer, I must be on the Gas Safe Register (official gas registration body in the UK) to be legally allowed to carry out gas work. I retrain every 5 years, get retested and keep up to date with changes in gas safety.


Getting it right


On a practical level once I’m on site, ventilation and flueing are crucial aspects in a plant room with standards I have to adhere to. Failure to consider them can be harmful for life. Through years of experience, you get an initial feel for correct sizing just by sight. Once I enter a plant room, I take a good look around to get an idea of the ventilation. A few grills might not look sufficient but can be in some cases. That’s why everything is assessed and measured in accordance with guidelines.


Commissioning is not just about setting up a correctly-sized and efficient heating system, but ensures first and foremost a safe installation. Gas applications are a safety risk if not installed or checked properly. If a manufacturer’s engineer is looking at it, you can be assured he has the required in-depth knowledge of the product to set things right. It’s one way to give peace of mind, and also to ensure the long-term reliability of a heating system. This means contractors provide a safe heating system for their customers and from a manufacturer’s point of view, the products are set up the way they are intended to be. Carrying out commissioning is therefore beneficial for all parties involved. Dave Ward has been service engineer at Hamworthy Heating since he joined the company in 1998. He has been servicing and


commissioning heating systems in premises of all kinds – schools, town halls, churches, hotels – for almost two decades.


www.heatingandventilating.net


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50  |  Page 51  |  Page 52  |  Page 53  |  Page 54  |  Page 55  |  Page 56  |  Page 57  |  Page 58  |  Page 59  |  Page 60  |  Page 61  |  Page 62  |  Page 63  |  Page 64  |  Page 65  |  Page 66  |  Page 67  |  Page 68